Cce TV Repair: Common Faults and Solutions.
Search: Cce
Results: 4836
Results: 4836
Cce Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| CCE | D4201 0000 | Inoperative TD off | After a checkup in all power supplys 12 5 3.3 1.8V TD OK | I put a load at the 12V font I made a forced polarization at the 5VSB power supply the TV returned to work perfectly must static load! It is the tip !!! | Jhone eletronica |
| CCE | STILE D40 | Locking keyboard, locking picture, etc. | I thought it was the U5 regulator, it was the 3V3 U3, I also replaced some capacitors around the regulators to ensure | reginaldo moronte,eletronica junior caldas novas | |
| CCE | LH42G | No standby, power supply defect, adaptation of another power supply plate | For those who have not been able to raise the power supply, have the option of using Philco power supply. I used a MLT666 of PH32m2 pH32m3 | Reorganize the whip according to tensions (5V, 5VSB, 12V and PS-On), and inverter (24V and GND). After that, the pins will be left on/off and adj. Just join them respectively, then instead of the drive passing through the power supply, goes straight from the main sign to reverse. It is 100% | World TV - Sorocaba |
| CCE | LT32G | When turning on the power, fast red blinks and then flashing blue and it takes well until standby, after tightening Power it is flashing blue again takes well and does not light the backlight, illuminate with a flashlight is written CCE and is indefinitely, ie, processing stick, memories. sound uses memory 25L1606e. | I wrote to warn friends that this is not the memory U103, memory 25L1606e, because I physically rewrite the memory, I updated via pen drive and nothing. I removed the memory I recorded and put it on another sign that worked perfectly. | So I concluded that the defect is not a memory U103, unfortunately I could not solve, it must be the Flash Nand memory, this I did not replace, disappoint friends but will not time Iguel I lost thinking that the memory U103. | MIGUELTV |
| CCE | LT32G Gt1326ex d292 | LED is flashing blue and red | Don't turn on | ANAILTON | |
| CCE | D3201 CW3201 cce | Works for days and you doesn't start anymore | Ressold d7 | ressold diode d7 | mendes am |
| CCE | STYLE D46 | Sound OK, Dark Screen | Um capacitor 20pf x 6kv na pci lateral | Remove that av TV goes back to work because I didn't find the lamps | Warley |
| CCE | C390 | Sometimes it does not turn on or off after a short time. | 3V3 U2 regulator (is close to EEPRON). It was measuring 2.78v. | Just replace straight. | R-Tec |
| CCE | C420 | TV Normal turns on and works a time and then crashes with liter and a loud sprinkle noise. | Defect in the U5 TRASITOR REGULATOR OF 1.8 V | replace | RV ELETRONICA GYN |
| CCE | C420 | TV Normal turns on and works a time and then crashes with liter and a loud sprinkle noise. | Defect in the memory .. | replace or rewrite memory | RV ELETRONICA GYN |
| CCE | LN24GW | Nothing works | C.I. U12 - 9435 (actually a fet) Short on R208 | Eletrônica do Alemão | |
| CCE | L244 | Call everything normal, after 10 turns off from nothing. Calls again and the stay tied on is decreasing. | replace both capacitors at 12V power supply (1000UF X25V) | replace of the cited capacitors. | arock |
| CCE | LN24G | Does not turn on short at the entrance | CI 9435 Position U12 | UTI das tvs e microondas | |
| CCE | LV40G | Short circuit power supply Drive LED. | Q501 is FDD120AN15A0 and works the FET ME15N10-G on site. | If it works slightly darker with 70 volts on the LEDs, check/ replace I.C 500 (MP3394) at the power supply, because in my case PWM did not act when replace \\\ "Standard picture for dynamic for staff \\\" and I suspected I.C and really was. After exreplace I.C 500 MP3394 the voltage went to 81.5 volts in the LED exits. | MIGUELTV |
| CCE | STILE D3201 | Don't turn on, with the orange LED flashing | PFC CI in the short | replace the U1 with the number 1607b which is under the power supply plate, near the large capacitor | Wsmartcell |
| CCE | STILE D3201 | It turns on, lights Stanby, when tightening Power replaces green and nothing happens, then blinks error 7 in the power supply LED. | High tension T1 at the power supply, after suffering to the damn, as it takes the stroke to test another I already visualized the charred winding at one point of the traf. | replace T1 (MIP320g-a-T1/TLT-2796) of the MIP320G-HV0 power supply. Explaining line of reasoning: the 5 volts and power on font appeared and also the 12 volt and 24 power supply appeared, but only the 5 volts and power on, so I suspected the stuff after putting one point of the multimeter at the exit of the trafa and I could see a small high voltage spark and that's wsound I suspected the tread, but the TV was not lumped, so I discarded, so In the end everything worked out. | MIGUELTV |
| CCE | LT32G LT32G | Do not light the LEDs | Diode with altered internal capacity (it seems like joke) measuring this good, but in the equipment of the low capacitance. | Diodo D3 (SB5150) | Johnatan |
| CCE | STILE D3201 | Backlight access, without picture | Tsound was no 12V and 24V. Causes cold welds on the power supply plate | Eletrônica Cecé, Brumadinho MG | |
| CCE | HPS2997 | Without sound with picture | C661 470/16 with escape | replace | Hndrsn |
| CCE | TV - 2118 USP / AV | Reduced picture on the right side of the screen | R 307 of 330R and R 308 , R 309 of 1R | replace | Mauro Mascarenha Tel. (88) 981422821 Parazinho - ce |