Cce TV Repair: Common Faults and Solutions.
Search: Cce
Results: 4836
Results: 4836
Cce Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| CCE | HPS-1471 34BI | When plugging it into the socket and pressing any button, the LED would flash and it would not be possible to start. | Check primary, secondary, vertical, horizontal, and flyback power supply components | In my case it was the fr401 (1r for 1w, close to the flyback), I replaced it and the TV finally turned on. | Tiago C. Neves |
| CCE | HPS 1497 | The image doesn't turn on, the LED doesn't stop flashing. | Faulty flyback, low voltage on scrin pin | Replace the same | |
| CCE | STILE D32 | At 220 volts it even lights up the lamps and gives an image, at 110 the lamps blink a few times and the power supply shows error 11 (11 blinks). defect in the primary power supply pfc | Q6 smd transistor in the primary power supply open, did not feed the u1 approximately 16 volts. | Replacing u6 (It's a pnp transistor) | MIGUELTV |
| CCE | 2171 FS | This TV had the LED off and tsound was a strange noise at the power supply: | I changed the fly back and it solved the problem, I put the bsc25-0206h in and it worked. Help others and God will help you too; | ELETRONICA NOSSA SENHORA APARECIDA | |
| CCE | 2171 FS | LED doesn't turn on | Resistor fr 402 of 1Ω behind the fly back connected to diode 404. | ELETRONICA NOSSA SENHORA APARECIDA | |
| CCE | LT32G | Don't tune in | Change varicap from another cce board that is a similar model ln32g, etc. | reginaldo moronte,eletronica junior caldas novas | |
| CCE | TV 2118USP/AV | Low volume | R681 (smd) between the terminals of capacitor c666, remove it from the board | Remove the r681, smd, 22k from the board that is between the c666 terminals | MARCONES DE ARARIPINA-PE |
| CCE | TV 2918 USP/AV | Vertical closed at the bottom, and with lines on the screen. | C417, c424 and c428 amended. | MARCONES DE ARARIPINA-PE | |
| CCE | TV 2118USP/AV | Alloy with closed vertical, at the bottom, and retraction lines | C417 c424 and c428 swap all. | MARCONES DE ARARIPINA-PE | |
| CCE | TV 2918 USP/AV | Reduced frame, with lines. | Capacitors c417, c428 and c424, replace them all, and resolder them on the vertical output. | Replace c417 c428 and c424 | MARCONES DE ARARIPINA-PE |
| CCE | HPS-2118AVP | Low volume | Q101( bc337/25 ) grounded! close to the varicap. | In my case, I thought it would be better to replace it with a Kia7805. I just had to remove the resistor r412, and connect the middle pin, directly to ground. | Marcones de Araripina-PE |
| CCE | LN244W | Doesn't start. Standby LED does not light up | Ec4 capacitor main board | Replace it and run for the hug | XANDARE |
| CCE | TVS-2910FS | Does not turn on, standby LED is off, no secondary voltage | Capacitor c816 (470mfx400v) completely exhausted | Replacing capacitor c816 (primary power supply) | Bruno C. Rodrigues |
| CCE | C420 | Turns on normally, crashes with stripes on the screen and loud noise from the speakers. | Regulator u5 changed - normal voltage 1.8 volts | Pardal-X | |
| CCE | HPS-14XX HPS-20XX 34BI | Power supply with 70v and it doesn't go up | R817 amended | Replace r817 | Fofão estância |
| CCE | C4601I | Blinking but not turning on | Ld33 regulator | I replaced the LD33 regulator and the capacitor near it, the TV started working again! | Marcelo |
| CCE | LN39G GT-1326EX-E39 | Does not turn on, the stand-by LED is weak, varying in brightness, sometimes it turns on. | Low voltage and varying in the ci u2 regulator 3.3v due to the resistor r29 being cold soldered. The resistor was resoldered and the voltage of 3.3v was stabilized and turned on again. | Cezz@r Augusto | |
| CCE | HPS 2118 AV | Horizontal dark stripe on the side | Ceramic capacitor c434 between flay back and the anode of the abl diode | Raimundo | |
| CCE | C4601I | Turns on the logo appears and turns off the backlight | Inverter output capacitors ck15a ck15b + capacitor +b doubtful to change too | reginaldo moronte,eletronica junior caldas novas | |
| CCE | STILE D42 GT309PX-V302 | Noise from the power supply turns on then turns off the green LED lamps on the power supply blinking | Change capacitor ec3 power supply 180n for 450v solved | Nao | Jonatas Silva Ribeiro |