Mitsubishi TV Repair: Common Faults and Solutions.
Search: Mitsubishi
Results: 1346
Results: 1346
Mitsubishi Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI | BDS28WS 11AK19 11AK19 | Entering service mode | First enter the installation menu, then press 4, 7, 2 & 5 respectively (another possibility is 2,3,5,7) | ||
| MITSUBISHI | BDS28WS 11AK19 11AK19 | Dead apart from led dimly flashing green - will sw on & off - no eht and ht (150v) low at 102v | D807 in psu leaky | ||
| MITSUBISHI | 11AK19 11AK19 | Dim band of light 3/4 up screen - sound ok | D408 8v2 zener leaky | ||
| MITSUBISHI | BLACK DIAMOND 11AK19PRO 11AK19 | No pic then e/w faulty | C630 dry jointed, when resoldered had e/w fault - q603 leaky fitted buk457-600b in lieu also l604 faulty | ||
| MITSUBISHI | BLACK DIAMOND 11AK19PRO 11AK19 | Dead with d829 uf5407 ht rect s/c | D807 ba159 s/c, chopper tr s/c 2sk2545 - used 2sk1507 in lieu, r817 2r2 5w o/c | ||
| MITSUBISHI | BDS28WS11AK19PRO 11AK19 | Won't come out of st/by when sw to st/by aft operating for more than 5 mins | Sw mode tr replaced | ||
| MITSUBISHI | BDS28WS11AK19PRO 11AK19 | Sw to st/by after 2 mins - g led flashes when trying to come out of st/by | D505 2v4 zener sm conn to pin 33 ic501 leaky | ||
| MITSUBISHI | BDS28WS11AK19PRO 11AK19 | Dead | Q605 bu2508af, c630 390nf 250v, c626 12nf 2000v, l604 e/w coil, tr601 line drive transformer, l604 15mh coil, r629 27r, d807 ba159, d605 ba159, d606 ba159, c835 1nf 1000v | ||
| MITSUBISHI | BDS28WS 11AK19PRO 11AK19 | Int shuts down to st/by with led dimming - usually at start up | Focus spark gap arcing - replaced crt skt 30001855 ?1.39 from seme | ||
| MITSUBISHI | BDS28WS 11AK19 11AK19 | Int blows loptr at sw on - also ew fet & r629 could be damaged | Dry joint c630 | ||
| MITSUBISHI | HS MX1 | No color | Switched to mesecam | Force to pal pin 1 of ic 6a0 go to low level remove r 6n2 | |
| MITSUBISHI | HS MX1 | No display and won't turn on | Q 901 = already 101 | Sub q901 = bc 638 | |
| MITSUBISHI | HS MX1 | No display and won't turn on | Q 901 = already 101 | Sub q901 = bc 638 | |
| MITSUBISHI | CT 14M1 EPM | With little sound and noise | Qaa = JK501 = SZ15 | ||
| MITSUBISHI | HS MX1 | No color | Switched to me-secam | Force pal pin 1 of ic 6a0 to go to low level remove r 6n2 | |
| MITSUBISHI | CT25M1 | E/w does not adjust well vertically folded at the bottom | Sub c587 = 2,7n 2000volt | ||
| MITSUBISHI | CT25M1 | E/w does not adjust well vertically folded at the bottom | Sub c587 = 2,7n 2000volt | ||
| MITSUBISHI | TC-1498 | Defects, no image and no sound, normal 33v voltage, good selector. | Cag trimpot altered, replace with a new one. | ||
| MITSUBISHI | TC-1631 | Call whenever you want. | Change resistance r-916 or r-915 of 150r | ||
| MITSUBISHI | TC-2030 | Defect becomes negative after some time. | The 10k x 50volt ceramic capacitor (.01µf) was replaced. Ceramic shorted. |