Mitsubishi TC-20 TV Repair: Common Faults and Solutions.
Search: Mitsubishi TC-20
Results: 173
Results: 173
Mitsubishi TC-20 Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI | TC-2010 | Image kind of erased, blurred, similar to a weak tube | Abl capacitor pin near the flyback on the acl output with cold solder | Resolder the capacitor and problem solved | |
| MITSUBISHI | TC-2009 | Half closed image | Altered vertical ci do la7837 | paulistana pi | |
| MITSUBISHI | TC-2010 | Very dark image | Capacitor c653 | Eletronica tensao R Jacuipe | |
| MITSUBISHI | TC-2010 | Very dark image | Capacitor c653 | Tec flavio | |
| MITSUBISHI | TC-2018 PS | Does not oscillate | R571 does more b fly.black | JOSE HUMBERTO F SANTOS | |
| MITSUBISHI | TC-2018PS | Stand-by LED access activates the key to turn on and nothing happens, | After changing several suspicious components with no results, I decided to change the ci 101 microprocessor and the TV returned to normal operation. | Val | |
| MITSUBISHI | TC-2018PS | Saturated image, no sound | Defective 7809 regulator | Component replacement. | NiloTech |
| MITSUBISHI | TC-2099 | Doesn't start. LED flashing. | C907 (22x100v), power supply. | Eletrônica R-Tec | |
| MITSUBISHI | TC-2099 | It doesn't turn on with a very low noise at the power supply, change the capacitor -c907, I changed it and I'm fine | Ss07 | joãotc | |
| MITSUBISHI | TC-2099 | Image with interference without synchronization | Tda4662, c208,c705 | Replace | ELETROCLAUDIOPE AGUAS BELAS |
| MITSUBISHI | TC-1499 TC-2099 TC-20A | LED lights up and then turns off at high power | R952 changed and c907 with esr changed | I replaced the r952, after that the LED was just blinking, I replaced the c907 and closed the lid | Bruno Capozzoli |
| MITSUBISHI | TC-1499 TC-2099 TC-20A | Just measure on a high scale, replace and that's it. | C920 with leak | Just measure on a high scale, replace and that's it. | Bruno Capozzoli |
| MITSUBISHI | TC-1499 TC-2099 TC-20A | Just turn on the LED | D953 zener 6,8v | Tsound is no point in measuring what measures as good, you have to replace it | Bruno Capozzoli |
| MITSUBISHI | TC-20 | Dull TV, horizontal bands behind the image, remote control accesses the menu, but does not navigate through the options | Horizontal bands, cause: c705 and c703 of 1mf x 50 volts, no brightness, cause: adjustment of the scrim screen and brightness in the TV menu, remote control accesses the menu, but does not navigate the options: tsound are several parallel controls that do not have the function keys | This TV was a gift from a Greek that was donated to me, after years of leaning on it I decided to touch it, when I turned it on, only a light blue screen appeared, I know that this TV has this screen protection when tsound was no signal, I connected it to the antenna, the image appeared, but without brightness , I acted on the screen and it showed an image, but with horizontal bands behind the image, I replaced the c705 and c703 of 1mf x 50 volts which were shorted and resolved, I bought a remote control that accessed everything except navigating the menu to adjust them, so I researched and got tips that said it included the eeprom, I remembered that this TV came with a remote control when I got it, I looked for it... I even thought I repaired it because it was defective, I went into the menu, I adjusted the brightness, color, etc. I re-adjusted the screen and blz, the parallel control did not have function keys to navigate the menu | ivan@ |
| MITSUBISHI | TC-2098 | Does not turn on, stand-by LED is off | Short ic901(str-s6707), res.r900/902/905 open, fuse f901 open | Replace them all, check cap.elet.c905/906/907. | jheliocavalcanti |
| MITSUBISHI | TC-2009 | The device has a loud noise at the power supply. | Electrolytic capacitor: c-903, main supply. | Replaces c-903, 220μF x 400v. it's ok! | Cláudio Ribeiro, TECNOSAT ELETRÔNICA E INFORMÁTICA, Jataí-Go, This email address is being protected from spambots. You need JavaScript enabled to view it. |
| MITSUBISHI | TC-2009 | Channel locked | With the control, enter the locked channel/menu/tuning/channel lock/password number and press the channel return key 4 times (the one with two arrows facing each other) | After unlocking, to tune go to automatic tuning, press and hold vol+ | paulorusso |
| MITSUBISHI | TC-2098 | Power supply arms and disarms | 07. | Replace. | Edigar de Souza Moulaz |
| MITSUBISHI | TC-2009 | Diagonal lines over the image, on all channels, also on av. | C-206 | Replace it | Ronan Nolasco |
| MITSUBISHI | TC-2099 | LED flashing, power supply does not stabilize | R908 open near c907 | Resolved by replacing the 10k r908 | PATRICK |