Mitsubishi TC-2018 TV Repair: Common Faults and Solutions.


AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HISENSE
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: Mitsubishi TC-2018
Results: 21

Mitsubishi TC-2018 Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
MITSUBISHI TC-2018 PS
Does not oscillateR571 does more b fly.blackJOSE HUMBERTO F SANTOS
MITSUBISHI TC-2018PS
Stand-by LED access activates the key to turn on and nothing happens,After changing several suspicious components with no results, I decided to change the ci 101 microprocessor and the TV returned to normal operation.Val
MITSUBISHITC-2018PS
Saturated image, no soundDefective 7809 regulatorComponent replacement.NiloTech
MITSUBISHITC-2018
Stays on standbyCheck ic 251, regulator 7809 with problempardalzito
MITSUBISHITC-2018
Power supply does not operate. (it is not even on standby)C 913 aberto (220mf x 25v)TVCompany
MITSUBISHITC-2018PS
No colorsMicroReplace micro m5277joaomvjr
MITSUBISHITC-2018PS
When cold tune out warping imageVaricapVaricap resoldering or replacement
MITSUBISHITC-2018
You plug the TV into the socket and it oscillates for 3s and goes into protection mode.Protection activatedLook at the most critical components such as flyback, horizontal and vertical output, if these have a bullet, measure the voltages of the 901 regulator (str f5654), if the voltages are ok, turn off the diode (953), 18.6v, the TV will turn on and oscillate normally and it will show wsound the defect is, in my case it was the vertical output and the IC (701), this one came from another workshop I believe it was just the vertical one, because the IC 701 had new solder, unfortunately tsound is a workshop that uses From this bad faith, a hugffeet
MITSUBISHITC-2018
TV cutting out sound and not obeying commands either on the panel or on the remote control5v supply on the clock and date line and high vccCheck the entire power supply including the load diodes (connected to ground) the power supply must be 5v roundCSOM-(066)34231060
MITSUBISHITC-2018PS
TV turns off by itselfResolder or pine gnd do fly backclaudio eletronica evolusom olimpia sp
MITSUBISHITC-2018PS
I'm sound, muteMicro m37372m6-325spDevice without sound, it was on mute, when I replaced the computer the device started working again.spectroneletronica
MITSUBISHITC-2018
Std-by led on, does not startSolda fria no fly back
MITSUBISHITC-2018
Stays on standbyCheck ic 251, regulator 7809 with problempardalzito
MITSUBISHITC-2018
Power supply does not operate. (it is not even on standby)C 913 aberto (220mf x 25v)TVCompany
MITSUBISHITC-2018PS
No colorsMicroReplace micro m5277joaomvjr
MITSUBISHITC-2018PS
When cold tune out warping imageVaricapVaricap resoldering or replacement
MITSUBISHITC-2018
You plug the TV into the socket and it oscillates for 3s and goes into protection mode.Protection activatedLook at the most critical components such as flyback, horizontal and vertical output, if these have a bullet, measure the voltages of the 901 regulator (str f5654), if the voltages are ok, turn off the diode (953), 18.6v, the TV will turn on and oscillate normally and it will show where the defect is, in my case it was the vertical output and the IC (701), this one came from another workshop I believe it was just the vertical one, because the IC 701 had new solder, unfortunately there is a workshop that uses From this bad faith, a hugffeet
MITSUBISHITC-2018
TV cutting out sound and not obeying commands either on the panel or on the remote control5v supply on the clock and date line and high vccCheck the entire power supply including the load diodes (connected to ground) the power supply must be 5v roundCSOM-(066)34231060
MITSUBISHITC-2018PS
TV turns off by itselfResolder or pine gnd do fly backclaudio eletronica evolusom olimpia sp
MITSUBISHITC-2018PS
No sound, mutedMicro m37372m6-325spDevice without sound, it was on mute, when I replaced the computer the device started working again.spectroneletronica