PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14173
Results: 14173
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 20PT326A | This TV arrived at the workshop with the LED blinking and when checking the power supply I found the capacitor c2409 of 47mf x 160 v exhausted, and when changing it the TV continued to blink the LED and did not stabilize the 95 volt +b, | So I went deeper and went close to the IC 7220 (integrated in the power supply), next to it there are two electrolytic capacitorsoc2540 of 100mf x 25v and the c2430 of 1mf x 50v, I exchanged them and the TV remained intact, don't forget to resolder it It was totally worth it for a lot of raw soldering too | So guys, when you get this problem, you don't even need to measure it on the capacimeter because it was good... this electronic thing sometimes drives us crazy lol | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILIPS | 29PT 4641/78 TCI-A10S | Dull image | Vertical was closed but has already been resolved | JOAB RODRIGUES | |
| PHILIPS | 26PLF3404_78 TPS2.1LLA | Without image, the lamps no longer light up with normal audio | Inverter transformer with normal voltage but getting very hot | Replace the inverter transformer problem solved | predador |
| PHILIPS | 20PT326A | The TV had a chirping power supply and the +b was oscillating between 70 and 87 volts and there was no high voltage! | Integrated from the bad power supply, the mc44608 after I changed it and the TV was broken | HELIOMAR DE VALADARES MINAS | |
| PHILIPS | 29PT458 L01 | Power supply ok but doesn't turn on stby led turns on and off no remote control but doesn't oscillate 8817 | R3491=10k open is in base d 7461= bc337 close to the hor driver | I replace everything, I'm back to normal, hugs all my friends, profession | marcos melo; cascavel ce |
| PHILIPS | 29PT458 L01 | No glare no contrast +b with 127 v 8817 | R 3481= 12k 3482=12k it stays in series/ abl open it stays on pin 10 d flyback | Replace of the same everything came back ok | marcos melo; cascavel ce |
| PHILIPS | 21PT6456/78 | Dark screen. with normal characters and sound | R3442 de100k aulado do flyback | Neto Wolff.Riba.Ma. | |
| PHILIPS | 29PT4643/78 | Vertical closed and folded at the top of the screen | C-2465-22mf/100 | dione | |
| PHILIPS | PT3331 | Thin colored lines at the top of the screen vertically | Capacitor in position c 2460, value 663/250 | Replacelo | moroni eletronica |
| PHILIPS | 21PT5433/78R | Normal image and sound, but after 5 seconds it turns off! | C 2503 of 220 mf x 450 v at the power supply ! | Luis araujo (teia) Pará | |
| PHILIPS | 29PT-9457 | It doesn't work/ there is 3v on pin 124 of the computer and nothing. | Micro blunder | I replaced the micro and ok! | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILIPS | TV2922 LEM10/FS8 | Burns the horizontal transistor. high power supply. | Change the power supply resistor 851, open or altered, of the secondary power supply. | João SF. | |
| PHILIPS | 21PT5433 L03.1LAA | I replaced it / bd135 it was ok | Q 7494 / bc337/25 heating | I replaced it / bd135 it was ok | betoteck |
| PHILIPS | 29PT5642/78 L04LS1 | Cvi (component video), with a reddish image even without signal. after eeprom change | Eeprom mismatch | Enter sam mode go to nvm editor, in the adr option select 0x003e 62 and replace the val option to 0x000f 15 (this value refers to blor (black level off-set red), if necessary also adjust the blogreen accessed by adr 0x003f 63 and changing the val to obtain the best black level (without signal) obs after each adjustment is selected select the option store?-> .to confirm the adjustment simply replace the function and return to cvi. | Wagner |
| PHILIPS | 29PT5642 L04LS1 | Comes with no sound, poor width, after a while normal sound | Checked pin 84 of the Hercules with low voltage (~4.4v). internal leakage in the pin only. solution: apply a 7808 regulator ci in place of r3975 (150Ω/1w), thus guaranteeing the power supply. I did this to avoid changing the ci (due to its high cost). | NelsinhoPira | |
| PHILIPS | 20PT3336 | No image, sound and normal osd | R-3442(100k) on the eht line | Marcelo Jose | |
| PHILIPS | 20PT228/78 L01 2LAA | Green screen with retrace lines and returning to the stand bay | Change resistor on tube board r 3324 on rgb line | Tecnico Jose Adriano | |
| PHILIPS | 20PT3331/78R | It's burning the 2k2 r3527 at the power supply! | Change the ci-tea 1506t at the power supply! | Luis Araujo (teia) | |
| PHILIPS | 29PT4641 | Image shifted to the left, i.e. image with a horizontal black band on the left side of the screen | C2486 ceramic of 27pf whereas the diagram shows it as 100pf | After the replace it was fillet. tip I got on a Spanish electronics forum | JOSÉ GUSMÃO |
| PHILIPS | 21PT5437/78R | With the white screen without image and thin horizontal stripes! | 100k 3442 resistor near flyback | Luis Araujo (teia) |