Search: PHILIPS
Results: 14173

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPS47MF437B/37
TPM2.0U LA
No image appearsInverter defect with swollen capacitors on the platesReplace of capacitors and also the two integrated on the two boardsjohnny busnadiego
PHILIPS42MF437B/37
TPM2.0U LA
No image appearsInverter defect with swollen capacitors on the platesReplace of capacitors and also the two integrated on the two boardsjohnny busnadiego
PHILIPS37MF437B/37
TPM2.0U LA
No image appearsInverter defect with swollen capacitors on the platesReplace of capacitors and also the two integrated on the two boardsjohnny busnadiego
PHILIPS20PT222A
L7L
Screen does not work correctly, retrace listsR3341 100homsReplace r3341 100homsjohnny busnadiego
PHILIPS42PFL3403
LC8.2L-LA
After +/- 20 minutes screen goes black sound remainsInverter transformer with cold welding.ELETROFEPAR
PHILIPSMCM595/19
Sound output short mosfet 18nq11tElectrical overload led to burning,As the 18nq11t mosfet didn't think so, it was replaced with the p14nf12fp and it works like a charmluismar
PHILIPS21PT9467 C/78
21PT9467 C/78
Vertical zipper with stripe at the bottomCi tda4865 ajIs to replaceozenildo alves da silva
PHILIPS29PT4635
Vertical closed at the topResistor 3464 ,220r openGilberto
PHILIPS20GL1044/78R
Vertical open but with thick lines throughout the image (venetian type)Replace the resistor r 3415 in parallel with the vertical coil and remove the terminals from it and resolder the wire directly onto the board.caio
PHILIPS29PT4635
Vertical serrilhadoChap. ceramic 0.22uf63v posicao 2409Continental
PHILIPS29PT4631/78R
L01.1L
Turns on, then turns off by itself, then turns on by itself but turns off again( c2455 (47µfx25v ) e ( q7461 (bc337 )Replace the components mentioned, and it works normally again.Eletrônica Heinz
PHILIPS29PT 5642/78
TV buzzing fly back, TV has a strong buzzing sound on the fly back, burning resistor 3440, burning the transistor q 7406, and with overheating in the horizontal output, the screen appears closed horizontally, completely out of horizontal frequency sawtooth effect.The fet transistor of the horizontal drive, the 7404 it works with an internal diode, the diode is shorted, the transistor is the si 2306 dsReplace the 7404 transistor, the problem is that you can't find it to buy anywhereEletrônica do Ricardo
PHILIPS21PT5437
No video just charactersResistor r3442 (100k) abertoThis email address is being protected from spambots. You need JavaScript enabled to view it.Bruno Nicacio
PHILIPS29PT5642
Device inoperative, power supply does not start.9v1 zener diode 6573 with leakage. (almost in short circuit)9v1 zener diode 6573 replacement.wagguinho
PHILIPS29PT4640
Television inoperative (horizontal does not start) normal power supplys reacts to the remote control, but does not work.6462 9v1 zener diode leaking (almost short-circuited) replace it.Replace d6462 zener diode 9v1.wagguinho
PHILIPS32PD6932/78R
TV doesn't turn on, only the standby light comes onTransitor 7461,7463 aberto bc337,bc327Gilberto
PHILIPS21PT434A
The TV just stays on standby and when you turn it on it flashes 4 times and goes back to standby againIn this case, what I caught was simply an unusual occurrence. The TV had already been screwed by someone else and the technician's horse left a bridge connecting the horizontal driver with a clue of ours that it was hard to find out, see, just find out because I went to measure the impendances of the drive and it was going directly to all the pinsJust remove the bridge and it works fineThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPSPT4635/78R
Horizontal burningAfter changing bc 337/25(7461), 327/25(7463), cap 2455, I changed the drive transformer (5461) and bingo!Trafo do drive(5461)audio e video
PHILIPS20PT3331/78R
Power supply gave a peak and went into protection, going into protectionI found a lack of 12v power supply that is generated from the flyback to the vertical output, r3445 on pin 8 of the flyback open.Alvanyr This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS21PT5433/78R
How to test the verticalThe vertical one has two transistors, they are called married one npn another pnp the collector of the npn has 20v +b the npn has 12v -b in the middle of the two transistors we have to have 0v you can measure it on the connector itself that goes to the deflector coil if one appears voltage, the vertical circuit is defective and it could be the transistors, some component around them connected to them or the IC does everything that is not providing the sawtooth etc.Miltom eletronica micro e epron