PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14173
Results: 14173
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 25PT 848 L01 1LAA | Turning off after about 2 minutes | Screen adjustment | Sergio Luiz | |
PHILIPS | PT4131 | Turns on but vertical does not open | 7491 change directly if the voltage on pin 14 of the computer is not 8v | junior | |
PHILIPS | 14PT519A/78 | Channel skipping | C2606 no pino 80 do ic7200 | Osmildo J Silva. Pontes e Lacerda MT | |
PHILIPS | 14 PT | Dark picture with/normal sound | Open resistor r3425 change and that's it, blz | ||
PHILIPS | 21PT4533 | Turns it on and before the image appears it turns off the LED and it won't turn on again, just unplug it. she returns and repeats the same procedure | Defective tube socket | Replace the same one for a new one | eletroclaudio aguas belas |
PHILIPS | 20PT3336 | When turning on the TV you notice that it generates high voltage but then turns off without lighting up the filament | The filament track on the tube plate was broken | I redid the TV track, it worked normally | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILIPS | 21PT467/78 | Vertical closed normal output | 1st open resistor 3445 | Replace and run for the hug | Sebastião Nedina |
PHILIPS | 29PT552A/78R | LED blinks and the TV does not turn on, the power supply and voltages are ok but the TV does not oscillate, it does not generate high voltage. | C2457 470nf dry, at the output of the horizontal coil, I replaced it and it worked. | ||
PHILIPS | 29PT9467 | Preso em stand-by | L105 open, ic201 in reset | renato tranca forte | |
PHILIPS | 21PT9467 | Vertical closed and circulating from the middle to the top to the top and stays stinging like a fluorescent to light | C316 r310 r318 open and the vertical output ic351 tda4865aj and d304 and d305 shorted | Replace them all | eletroclaudio aguas belas |
PHILIPS | 21PT438/538/29PT558/658 LO1.1L.AA | Lines at the top | C2476-2k7 - | + scrape glue underneath | milton |
PHILIPS | 21PT438/538/29PT558/658 LO1.1L.AA | Lines at the top | C2476-2k7 + scrape glue underneath | milton | |
PHILIPS | 14PT3131/78R | Turns on with vertical stripes and turns off | Broken trail | Call (j9518) to (c2447) resolved | NILTON-AVARÉ-SP |
PHILIPS | 14PT110 | When you press the channel, the LED blinks a few times and it doesn't turn on | Resolder c 2442 or replace it (the same and smd) | ANTONIO NOBREGA [PATOS.PB] | |
PHILIPS | 29PT5408/01 L04E.AA | It only worked for a few seconds. The LED blinked 5+11 times. | Trc with unbalanced gain. | Cleaning the cannons (rejuvenation) and it was ok. | Cunhas |
PHILIPS | 29PT4635 LINHA PT | TV turns on and off or is already activating the protection | The burning of the bu4508 is due to excessive heating, changing the gain of the transistors 7461 and 7463 for better performance of the device, you can place the bd136 and bd137 transistors in their respective places and also change the 47x25v capacitor c2455 it will no longer bother you | berga | |
PHILIPS | 14PT110 | When I pressed channel, the LED gave a few quick blinks and it didn't turn on. | C 2453 1000uf 35v there is no point in measuring, you can change it directly | ANTONIO NOBREGA [PATOS.PB] | |
PHILIPS | 105S5 | ~1mm horizontal line in image | Loose welds on c710 and r720 | Resolder c710 and r720 (which are located very close to the fly-back), or even a possible replace of components | Dark Fox |
PHILIPS | 29PT5645 | Turns on with black screen and three lines and turns off - vertical | D6457 smd in short and elect cap. from the vertical outlet | maxell | |
PHILIPS | 14PT3331/78R | Sem audio no fi (off normal) | C2201 e c2202 | Replace the two close to pin 31 of the handyman | Jarbas Santos |