PHILIPS TV Repair: Common Faults and Solutions.

Search: PHILIPS
Results: 14173

PHILIPS Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem
PHILIPS	FL1.6	Adjustment of white balance and cut-off	Adjustment of white balance and cut-off --------------------------------------- the white balance and cut-off adjustment instructions given on page 7.5 of the fl1.6 aa chassis manual require clarification as follows. manuals: gb 4822 727 18914 nl 482
PHILIPS	FL1.6	50hz buzz noticable through speaker	Check/replace ic7680 on the ssp - tda8425, pseudo stereo ic. (4822 209 63734).
PHILIPS	FL1.6	22av1440 is switched on by external vcr when fl1 is switched off	Connect 4 diodes of type bat 85 to inputs of ic7630 on ssp. 1 diode between pin 3/ic7630 and +5v, cathode to +5v. 1 diode between pin 5/ic7630 and +5v, cathode to +5v. 1 diode between pin 3/ic7630 and -8v, anode to -8v. 1 diode between pin 5/ic7630 and -8
PHILIPS	FL1.6	100hz cross	Possible solutions: 1. interrupt on the ssp the 50hz y-signal, between pin 11 position ic7324 (tda4568) and pin 11 position ic7395 (tda8443), by deleting position 4302. repair the connection by means of a shielded cable of 16cm long, m
PHILIPS	FL1.6	+141 is 75v when disconnecting hardware protection (prot signal).	When disconnected hardware protection, output voltage was 75v. apply sops repair kit (4822 310 31993).
PHILIPS	FL1.6	"on" led blinks. no control menu and/or "dark txt" and/or "no pip".	Options lost, mount motorola ic mc33164p (4822 209 31294) as described in service information fl1 93.02 (4822 727 19885).
PHILIPS	FL1.2S	Wrong synchronization, unstable colors	D6417 on the lsp dependent on temperature, check/replace (4822 130 81223)
PHILIPS	FL1.2S	Wrong service batch of st24c08cb1 memory ic's	Wrong service batch of st24c08cb1 memory ic's 4822 209 32283 ------------------------------------------------------------ temporarily a wrong batch of earom's has been delivered, causing the fault "nvm memory not write protected" after replacing the earom
PHILIPS	FL1.2S	Unstable picture, horizontal jitter.	Check/replace r3405 on the lsp. (4822 051 10303 for 50 hz sets; 4822 051 10333 for 100 hz sets).
PHILIPS	FL1.2S	Tuning does not function	Resistor r3240 on lsp in v-tuning wire broken.
PHILIPS	FL1.2S	Totally inoperative.	Transistors 7250 (bux85f; 4822 130 62509) and 7251 (bc848; 4822 130 61207) in microsops defective. or d6251 (llz-c5v6; 4822 130 80954) and r1250 (=r3230; 1Ω; 4822 052 10108) defective. or t7270 (bd825; 4822 130 41746) or t7201 (bc857c; 5322 130 427
PHILIPS	FL1.2S	Total inoperative, leds blinking, error 99	Check and replace if necessary c2504 and/or 2505 (2kv hrr) on the large signal panel. replace by a 3kv15 hr-r capacitor if possible: 820pf 4822 126 13152 1nf 4822 126 13153 1,2nf 4822 126 13154 1,5nf 4822 126 13155 1,8nf 4822 126 13156 2,
PHILIPS	FL1.2S	Ticking noise and line in picture	Transistor 7381 (bc848c; 5322 130 42136) defective when hot.
PHILIPS	FL1.2S	Synchronization, picture disappears	D6703 and t7704 defective on picture tube panel.
PHILIPS	FL1.2S	Switch-off spot visible longer than 5 seconds.	1) change item c2518 on the lsp into 10uf 250v (4822 124 23494). 2) for 29" and 33". as service solution the eht cable can be replaced by 4822 218 21041. this eht cable with bleeder provides a faster discharge time. remarks : 1) so
PHILIPS	FL1.2S	Spook in picture	Use special antenna cables. codenumbers: 4822 321 61224 pal 1 meter 4822 321 61225 pal 2 meter 4822 321 61226 secam 1 meter 4822 321 61227 secam 2 meter
PHILIPS	FL1.2S	Spare parts remote control rc64xx	Spare parts remote control rc64xx --------------------------------- codenumbers for part of the rc64xx remote control: flap right 4822 432 92716 flap left 4822 432 92715 battery lid (cover) 4822 432 92714
PHILIPS	FL1.2S	Pip picture not in order.	Check r3345 (4822 111 41424) in pip unit, check ic7755 (4822 209 63423).
PHILIPS	FL1.2S	Picture twists from top	Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c5v6; 4822 130 80954).
PHILIPS	FL1.2S	Picture twists from top	Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c3v6; 5322 130 34834 or bzx79/c10; 4822 130 61219)