PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14173
Results: 14173
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | FL1.16 | Overview of sops repair kits | Overview of sops repair kits ---------------------------- fl1.0 ag00 upto ag03 4822 310 20492 fl1.0 ag04 and higher 4822 310 31921 fl1.1 25" and 28" 4822 310 31919 fl1.1 33" 4822 310 31932 fl1.2 4822 310 31932 fl1.6 | ||
| PHILIPS | FL1.16 | Noise on high volume | Perform the following modifications on the ssp: add on position 3618 4,7nf (4822 122 31784) add on position 3619 jumper (4822 051 10008) connected in series from 2604/4610 to earth. change position 4610 into 1kΩ (4822 051 10102) | ||
| PHILIPS | FL1.16 | No sound, "on, standby, i" leds blinking | 10mhz crystal 1602 on the ssp defective, 4822 242 80276 | ||
| PHILIPS | FL1.16 | No colors in tv mode | Check ic7365 (tda4650) on the ssp (4822 209 30837) | ||
| PHILIPS | FL1.16 | Low frequency hum from subwoofer, buzz from right hand squeeter. | Check dc level on pin 1 and 9 of ic7011 (tda1521). if not correct, replace (4822 209 63913). | ||
| PHILIPS | FL1.16 | Low brightness txt and osd, picture ok | If this condition occurs, check the option codes. resetting the option code numbers as per the service manual provided the cure. | ||
| PHILIPS | FL1.16 | Jitter at ntsc reception. | Replace item 9459, connected to pin 13 of ic7400 on the lsp, into 220Ω (4822 116 52215). remarks : introduced in production in week 9335. | ||
| PHILIPS | FL1.16 | Jitter | In pip unit change the value of r3336 to 4k7. | ||
| PHILIPS | FL1.16 | How to enable/disable "child lock" | Press "menu" button on remote control. when the menu appears on the screen, you select "special features" (this expression is language dependent) within "special features", the "child lock" can be enabled or disabled. | ||
| PHILIPS | FL1.16 | Four dark bars over the picture. | The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672). | ||
| PHILIPS | FL1.16 | Faulty horizontal sync. (intermittent and temperature-sensitive) | Capacitor 2117 10nf on lfr box mechanically damaged. (4822 122 32422) | ||
| PHILIPS | FL1.16 | Faulty horizontal sync. (intermittent and temperature-sensitive) | Capacitor 2117 10nf on lfr box mechanically damaged. (4822 122 32422) | ||
| PHILIPS | FL1.16 | Distorted east-west & jitter on vertical side lines at switch-on. | In the fl1.16 and fl2.16: replace position t7610 on the lsp by bd536fi (4822 130 63508). delete position 2615. replace position 2611 on the lsp by 2,2 uf (4822 124 41576). replace position 3608 on the lsp by 1k (4822 051 10102). in the fl2.24: replace po | ||
| PHILIPS | FL1.16 | Distorted east-west & jitter on vertical side lines at switch-on. | Replace position c2611 on the large signal panel by a 1 uf capacitor: 4822 121 51319. remarks : the east-west distortion shows a barrel-shape. the jittering only occurs at the centre of vertical lines at the left- and right-hand side. after warm | ||
| PHILIPS | FL1.16 | Different heights of the characters in subtitling | (in the middle of the screen the characters have a smaller height). change position 2520 on the large signal panel from 390nf into 330nf 250v (4822 121 51612) and adjust the picture width again. | ||
| PHILIPS | FL1.16 | Dark picture, only green led, no menu or osd. | +5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954). | ||
| PHILIPS | FL1.16 | Dark fuzzy picture. osd and menu not in focus. | +5v was 7.8v and +13v was 15.5v ic7551 (lm358n; 4822 209 70672) defective. | ||
| PHILIPS | FL1.16 | Crazy behaviour: no response from rc or controls. | Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v82 (4822 900 10423). for easy mounting also the controlboard 7115 (on ssp) can be replaced by | ||
| PHILIPS | FL1.16 | Correction to service manual flx.14/16/17 | Correction to service manual flx.14/16/17 and flx.24/26/27. ----------------------------------------------------------- the code number of position 1200 (fuse 3,15 a) is wrong. the correct code number is 4822 070 33152. this fuse is situated on the lsp i | ||
| PHILIPS | FL1.16 | Correction to service manual | Correction to service manual ---------------------------- in service manual fl1/2.14, fl1/2.16, fl1.17 aa the code number of the scavem amplifier panel is wrong. the correct code number for this panel is 4822 212 31469. remarks : the code number |