Search: PHILIPS
Results: 14173

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPSFL1.10
No picture, sound is ok. error 00 99 07 15 09.Check r3480 and r3481 on the ssp. (2,7Ω safety resistor; 4822 052 10278).
PHILIPSFL1.10
No picture, only txt/menu/osd and sound.If voltage p13 tda4680 (ic7430) not 0v, t7182 is leaking. replace t7182 (bsr12; 5322 130 44743).
PHILIPSFL1.10
No colors in tv modeCheck ic7365 (tda4650) on the ssp (4822 209 30837)
PHILIPSFL1.10
Modification: stability of +13vModification: stability of +13v ------------------------------- r3241 on the large signal panel is changed into 6,8Ω 10% 5w (4822 113 80644). remarks : introduced in production in week 9335.
PHILIPSFL1.10
Modification on eco-combfilterModification on eco-combfilter ------------------------------ to increase the bandwidth the following items on the eco-combfilter are changed: - item 3043 changed into 1k (4822 051 10102) - item 3045 changed into jumper (4822 051 10008) - item 3
PHILIPSFL1.10
Modification new eht plug with new lotModification new eht plug with new lot -------------------------------------- only for 21" sets in week 9340 the l.o.t. and the eht cable are changed. the lot (4822 140 10412) has been changed from 3122 138 3813.2 into 3122 138 3813.3. this is done becau
PHILIPSFL1.10
Low frequency hum from subwoofer, buzz from right hand squeeter.Check dc level on pin 1 and 9 of ic7011 (tda1521). if not correct, replace (4822 209 63913).
PHILIPSFL1.10
Low brightness txt and osd, picture okIf this condition occurs, check the option codes. resetting the option code numbers as per the service manual provided the cure.
PHILIPSFL1.10
JitterIn pip unit change the value of r3336 to 4k7.
PHILIPSFL1.10
How to enable/disable "child lock"Press "menu" button on remote control. when the menu appears on the screen, you select "special features" (this expression is language dependent) within "special features", the "child lock" can be enabled or disabled.
PHILIPSFL1.10
Horizontal oscillator not stable.For a more stable adjustment of the horizontal oscillator change the next items on the large signal panel: position 3405 from 30k into 33kΩ (4822 051 10333) position 3406 from 10k into 4k7Ω (4822 100 11319) remarks : introduced in producti
PHILIPSFL1.10
Goes to st/by at sw on & chan change - pic too bigHt high at 156v (141v), r3374 75k had increased in value
PHILIPSFL1.10
Four dark bars over the picture.The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672).
PHILIPSFL1.10
Fault guideSee tv mag nov 2000
PHILIPSFL1.10
Fall off position 3204 on the large signal panelFall off position 3204 on the large signal panel ------------------------------------------------ when position 3204 (ntc/ptc; 4822 116 40215) on the lsp is defect it is recommended to replace it by a ptc/ptc (4822 116 40253). together with this change al
PHILIPSFL1.10
Dead - no volts to mains capPositor ph95315 & fuse
PHILIPSFL1.10
Dark picture, only green led, no menu or osd.+5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954).
PHILIPSFL1.10
Crazy behaviour: no response from rc or controls.Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v82 (4822 900 10423). for easy mounting also the controlboard 7115 (on ssp) can be replaced by
PHILIPSFL1.10
Crazy behaviour: no response from rc or controls.Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v83 (4822 900 10506). for easy mounting also the controlboard 7115 (on ssp) can be replaced by
PHILIPSFL1.10
Correction to product survey 1996-4Correction to product survey 1996-4 (4822 727 21505) ---------------------------------------------------- on page pcs 41989 is mentioned at: fl1.10 ag11 and higher: control panel 4822 212 31708 fl1.17 ag20 : control panel 4822 212 31708 fl