Philips TV Repair: Common Faults and Solutions.
Search: Philips
Results: 14252
Results: 14252
Philips Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 43PFG6917/78 | Washed screen, without picture, but with lit back light. No power voltage on t_con plate | Perform reset procedure | With the device off the outlet, hold the commander of commands forward toward you. Then connect the device to the outlet, holding the cursor until the device turns on. Then just restart the settings | LABOTRON |
| PHILIPS | 43PFG6917 | TV without picture missing the 12 volts on the t.Con plate | Feed the T.Con with the 12 volts and turn on the TV will appear a service menu on the screen asking to do the recept and give a ok the TV will turn off to control and do all the procedures | RJ eletrônica | |
| PHILIPS | 42PFL5007 | Only Standby lit, don't turn or call | replace Q603 and Q581 (STK 0160) of the power supply for 7N50, and replace the Diode D107 for a 4007, success! | Matrix10y | |
| PHILIPS | 50PUG7907/78 | Call with washed screen without picture, sometimes does not turn on | It has all the tense, except 12V display, in this case and corrupt software (Android). | At Jampear CI Q401 which releases the 12V to the display, the screen turns on recovery mode, releasing repower supply of resetting Android. At the end withdrawing the jamper. | Beto , eletrônica box 4 |
| PHILIPS | AZ1030 | The same fate, tu is moluk. | R (309) 100k Open, Tuner Power. | Wandercy | |
| PHILIPS | HTS3345/78 | It does not turn on, it does not light anything and when it turns on the drawer makes the EJECT and forcing the EJECT engine even after the drawer opens total. | power supply 1.8V on the missing main plate. replace without measuring the Didos below: | D201-D202-D203-D204, all are in4007. | MIGUELTV |
| PHILIPS | 58PUG6654/78 | Low power supply | Tsound is no current in T with | ....... | |
| PHILIPS | 47PFL8606D | Does not turn on, flashes standby error 3, tsound are 03 blinked. | Missing 12 volt power supply originating from the main power supply | Cold weld at the Trefo Secondary Terminal that provides 12 volts. | MIGUELTV |
| PHILIPS | 32PHG5102 | After replace the logic plate the picture came blurred | Mode of service ID panel from 214 pass to 224 | All ok | Medeiros Eletrõnica Barbacena MG |
| PHILIPS | 48PFG5000 | Main replace with negative picture | Reference ID of the wrong rear label in the case was 174 even placing the codes all correct continued picture | Used in my case in the mode of service panel ID 189 ... after a lot of headache solved, sir pole your angels sound ... | |
| PHILIPS | XXPFG5000 | Main replace with negative picture | Reference ID of the wrong rear label in the case was 174 even placing the codes all correct continued negative picture | Used in my case in the mode of service panel ID 189 ... after a lot of headache solved, sir pole your angels sound ... | |
| PHILIPS | 65PUG7406 | screen without video, lit LEDs | No VGL voltage (-7.8VDC), turning off flat on the CNX_L2 connector the TV works. | After testing I found a flad defective, exreplace it resolved | jjsantosneto |
| PHILIPS | 42PFL3604/78 | Only red led, not part, | C474 replace near the crystal on the main plate | C474 na PCI principal | Rodrigo cofferi |
| PHILIPS | 42PFG6519/78 | Back Light deleted | C9105 near Trafo 9101 with poor contact | Replace it | TECMIL/MILTON |
| PHILIPS | FWM653 | Flashing panel and not turning on | Check the 2 belts of the CD Reader | replace belts that he has returned to work | C13 eletronica |
| PHILIPS | 47PFG7109 | Normal alloy, the logo appears, comes channels shut down. It is in this intermittent loop. Sometimes it wages in HDMI or channel, does not respond to the remote control. Turning off the outlet resumes the loop. After a few time on, it returns to normal and does not connect to the internet. | Turn off the \\\ "wi-fi \\\" plate. Everything returns to normal. | Wi-Fi plate replace. | arock |
| PHILIPS | 42PFL3508G/78 | Don't turn on, stand by lit, 5V line marking ~ 3.2V sometimes turned on when I loose a Flat from TCC. | power supply Plate Line 5.2V replaced resistors 9337- 8K2, R9338 - 9K1 Problem Causer IC9304 - AS431AZTR. On the main plate on the 3V3 line the SMD C2104 capacitor | replace the IC9304 for TL431, if it does not yet 5V, evaluate the resistors. Check SMD capacitors of the main board all voltage lines must be consistent with the electric scheme. In my case was the C2104 - 22u. | André Luiz |
| PHILIPS | FW-C155 | Don't turn on, blink panel and go off | replace without testing transistors 7247 3213 3247 7244 7322, preferably uses BC338 instead of BC337 | HAHNRAHN | |
| PHILIPS | PHILIPS 32PFL3605D/78 Philips 32PFL3605D/78 | Black screen with background light and sound | SMD resistor of T-Com integrated on the plate at the bottom link >> External link ... Open from the main | Required resistor I made a video that shows the link well External Link. .. | X elétro |
| PHILIPS | 42PFL3403 | Killed, without standby | Replaced U101 damaged, C120 and D107 and on PCB IR Capacitor shortly next to the sensor |