Philips TV Repair: Common Faults and Solutions.
Search: Philips
Results: 14210
Results: 14210
Philips Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 47PFG7109 TPM14 3L LA | Without image, audio ok. | Burned out leds | Replace the led bars | Eletrônica Moises N.H |
PHILIPS | 43PHG5813 | No image with LED on | The t-con board does not receive 12v | Fb714 missing, broken or open - from underside of board near panel flat | Alessandro B. Barcelos |
PHILIPS | 43PHG5813 | Does not turn on or inoperative | Na main pci see 5v_stb no l701 and less than 5v_sw no c786 is entered | Replace Q706 (aon4421) | Alessandro B. Barcelos |
PHILIPS | 32PHG5813 | Does not turn on or inoperative | Na main pci see 5v_stb no l701 and less than 5v_sw no c786 is entered | Replace Q706 (aon4421) | Alessandro B. Barcelos |
PHILIPS | 32PHG5813 | If you are going to replace the main board for another size TV of the same phg5813 | Change the u405 memory and the adaptation will work. | Alessandro B. Barcelos | |
PHILIPS | 32PHG5813/78 | No image with LED on | The t-con board does not receive 12v | Fb714 missing, broken or open - from underside of board near panel flat | Alessandro B. Barcelos |
PHILIPS | AZ1134 | Cd doesn't play radio fails | POS Function Key (SW1) or (SW7-A) | Function switch replacement or repair | ahunaky |
PHILIPS | FWM998/78 POW600 | Sound turns on demo mode partially but does not start | +12v low voltage, it was measuring below 9v. In the region of the inductors l1 and l2 of the power supply, the solders were oxidized and tsound was that disgusting glue that after a while gives conductivity. | Redo the welds in the region and remove all this factory glue. Don't forget to sand the legs of the inductors and capacitors. | Tiago C. Neves |
PHILIPS | 46PFL7606 | Does not turn on, LED flashes 3x | Check q403 and q402 LED power supply circuit, one of them has a short circuit. | Mirage Eletrônica | |
PHILIPS | FW-C380 FW-C380 | Digital erased 4r7 open | Digital erased 4r7 open-3211 on board | "3211" resistor 4r7 on the power supply board | NEUPSX4 |
PHILIPS | 55PFG5100 0000 | Retrace or bands on the screen | Short display | Technical arrangements or workaround lol... on cn 3 I isolated 3 ways 40 to 43, it was clean and crystal clear qsl macanudo lol.... | Jhone Eletronica |
PHILIPS | 32PFL3404 | It turns on the sound, the video is loud, and the screen is bright, but then it turns off. | Support for two LCD lamps loose. | I resolved the two and reinforced the others. | Ademir tc |
PHILIPS | 32PFL5604 32PFL3404 | Does not turn on, the stand-by LED lights up and flashes quickly, but the relay does not hit, it does not accept commands via remote or keyboard | Power supply defect, 2r2 smd resistor position rb3, on the power supply primary, underside of the board, resistor changed to 15k, is close to the chopper transformer of the 3v3 power supply of the i.c3 fsq510 | Replace rb3 | MIGUELTV |
PHILIPS | 42PFL7007 | LED on does not turn on | Q603 at power supply | Tv técnica Prudentópolis | |
PHILIPS | 42PFL7007G | It doesn't turn on anything, not even the LED, it has 3.3v | Power supply q581 | Tv técnica Prudentópolis | |
PHILIPS | 40PFG5509/78 | Sem video, audio e backlight ok | Following a tip from colleague jorge tecnica paraná (capacitor cd7) tsound are two other capacitors in parallel to the cd7. | In my case, the short was on cd8 | DIEGO BOEIRA |
PHILIPS | 39PFL4707G/78 | Working however with backlight off | No voltage on the dim pin at the power supply, check ic8107 pin 5 and 6 for a short, also check ics 8101, 8102, 8103, 8104, 8105, 8106 for a short between pin 1 and 5 | Replaced ic8107 and ic8102,8106,8104 that were shorted, normalized the dim voltage and backlight working normally | INFOMARQUES |
PHILIPS | 42PFL5508G | Standby light on and won't turn on | Defective pfc power supply oscillator, ic9801 | Stiltec | |
PHILIPS | 43PFG6917/78 | Turns on and locks on logo | Disconnect the cable from the socket, with one hand move the cursor forward towards you (keyboard), with the cursor pressed forward connect the cable to the socket, an initializing message will appear, after that make the initial settings, channel tuning, etc. ,it will work perfectly | reginaldo moronte,eletronica junior caldas novas | |
PHILIPS | HTS3011 | Difficulty turning on, when you press the power key the standby LED flashes and comes back on. | C920 10uf 16v on power supply exhausted | Eletrônica Barbato |