Philips TV Repair: Common Faults and Solutions.
Search: Philips
Results: 14210
Results: 14210
Philips Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 42PFL3403 | Red standby press power turns it off but it doesn't turn on..just disconnect cn7. and calling the pw tv called back with cn7 everything came back normal | Disconnect cn7 connect and return with cn7 everything was ok.. lucky for me... | Helio | |
PHILIPS | FWP2000 | 32v power supply with 22v | Change r743 from 3k to 2k33 near tl smd and photo | Warley cesar | |
PHILIPS | 42PFL5008 42PFL5008 | TV turns on normally with no image backlight on | It was changed in the service menu then it turned on normally without image backlight on | You have to rewrite eeprom 464rk 24c64 position 7705 near the network cable connector - download https://www.mediafire.com/file/ya43m9kd5kp6vqj/dados_eeprom_tv_philips_placa_42pfl5008_464rk__24c64.rar/file | neupsx4 |
PHILIPS | 20PT120 20PT122 14PT120 | Doesn't tune in to the channel, it gets stuck | Eeprom defect [or enter service mode enter service mode by grounding pin 1 of the eeprom [or changing the memory with the recorded data[ | Go into service mode and check the addresses ho 1;al 1;po 1;ac 0 checking everything and just turn off the TV using the remote control and that's it | orlando lott |
PHILIPS | PHG5301/77 | No enciende stand by | Main board with fault | Replace main solders mi ro | Gordociri |
PHILIPS | 40PFL5606D/78 | TV stuck on logo screen | Software update | The corresponding model was updated on the manμFacturer's website, following the step by step, I formatted the 2.0 pen-drive in fat and not fat32, inserted it into the TV and kept trying until it turned on, as soon as it turned on, the update screen opened and I did the update, I didn't go into settings but directly into the update screen, it was completed and worked normally. | Rapha_X |
PHILIPS | 42PFL3403/78 | Philips 42pfl3403/78 stand by led blinks twice but does not turn on. | The TV turns on the stand by LED, accepts the power on command and after this command, press the channel + button when you can hear (very softly) the re1 relay engaging. At this moment, tsound was only a voltage of 3.3 volts because this relay had a bad internal contact. I dismantled the relay (it can be dismantled) and saw that the terminals were very far apart and that's why it armed but did not conduct (and the docking sound was very low). All I had to do was clean and twist it to bring the contacts closer together and the TV started working again. normally. | littlecarlos | |
PHILIPS | 42PFL5508 | Turns off doesn't work at 110v. Sometimes it doesn't turn on | R9319 1.5m (cleaning) ic9301 (0133e) | I put ci spc7011f. working perfectly. | ELETRÔNICA FBS |
PHILIPS | 14PT3131/78R L03.1 | Turns on and then turns off | Tube blur protection | Put three 4148 diodes with + on the tgb filament and the - connected to the blk, then just look for the focus and move on to another | Eletronicazetec |
PHILIPS | 14PT3336 78 | LED blinks and turns off secondary power supply drops to 0 | R 3543 200k | Replace the same | Edval Feitosa de Lima |
PHILIPS | 50PUG6102 | Burnt out backlight | Changing the busbars, be very careful, glued screen and vcon too | Reduce current by removing resistors bank of smd resistors, removing 3 on each side is enough | |
PHILIPS | 32PFL5604 | Relay hits and doesn't turn on, standby only flashes red, doesn't turn white | Faulty relay pcb power supply | Relay replace | |
PHILIPS | 50PUG6102 | Turns on without backlight | Replaced completely burned out backlight, even so it did not activate the buses, without voltage at the output | Replaced c8113, q8101 and r8101 in the primary and resolved | |
PHILIPS | 50PUG6101 | No backlight | Changing the complete backlight, it still wouldn't connect the buses, changing c8113, q8101 and r8101 in the primary and resolved | ||
PHILIPS | 42PFG6519 / LE50D1452 | Power supplys are compatible and have the same defect, backlight does not come on or after a while if we turn it off, the backlight does not come on. | In the primary one tsound is the i.c 9101 and on pin 5 a series of 03 1mega resistors are connected, two common resistors and one smd resistor, but both 1mega each, the smd changes around 100kΩ and that is enough for the TV to experience a backlight failure | SubstituiÇÃo do resistor r9101 1 megaΩ | MIGUELTV |
PHILIPS | 32PFL3403/78 | Does not turn on, nor does the LED light up | Q602, q603, (I put 11n60), c625, c626 (331k), r634 (0.1r) | Cece eletrônica Brumadinho MG | |
PHILIPS | 32PH5813 | Alternating colors, without video or audio, after changing the card, placing the same card as 43! | Change the IC u405, remove it from the original board and place it on the new board, | Replace the u405 from the original to the new board | Rodrigo cofferi |
PHILIPS | 26PFL3404/78 TP52.1L LA | Turns on and after +/- 30 seconds turns off completely | Ic901 failure (tny277pn) | Substituir o ic901 ( tny277pn) pcb 715g3214-3 | leitemarcellus |
PHILIPS | 40PFG4109 | TV turns on but no image, with the backlight off | Changing the LED bars, **attention** this TV has two versions of bars.. with 3 volt and 6 volt LEDs | rafaelmoraes99 | |
PHILIPS | 32PFL4017G/78 | Turns on with sound, and without the image. The LEDs at the bottom light up normally | Shorted capacitor on the t-con board caused the fuse to blow on the 12v input | After contracting the open fuse, researching I found the capacitor c214 shorted. After changing it and replacing the fuse, the TV was resolved. | Romildo Behend |