Search: Philips
Results: 14210

Philips Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPS DVP3005/BK
It only had the STB LED on, it wouldn't turn on at all1y faulty oscillator crystal was replaced and the device worked perfectly again
PHILIPS49PFG5001/78
Turns on normally in seconds turns offDefect in memory removed and rewritten resolvedLuis Aquino sparapan
PHILIPS 68PUG6513/78
TV doesn't work, nor does standby light up.Check the power supply if it has 10v, etc... check on the main board if tsound is 5v on the ci u708 (voltage +5v_stb on the board).Ci smd sy8366q - u708 defectiveEletrônica JM/Júlio
PHILIPS42PFL4908G/78
After turning it on, the becklight turned off, only sound came outCi (pf7900s)smd in position ic8103 cutting voltage on pin 1Replace the ci and go for the hugLS ELETRÔNICA
PHILIPS 40PFL3606D/78
Red light on, press power but it won't turn onBlue ceramic capacitor c502Replace the capacitor c502, it's very bad on this TVWilker
PHILIPS 40PFL3606
Back light comes on, gray screen and some lines.After checking the 750k, 240k and 10k resistors, without success adding a 150k resistor from the r750k to the capacitor next to it, terminal nodes on the IC side (inside the board).
PHILIPS32PHG6825/78
Doesn't startDiode d9105Replace the samePop Tron Mafra S.C.
PHILIPS20PT4331
Then turning offAdd 3 diodes to the tube plate to bypass the tube in the ik circuitPut diode and solvedorlando lott
PHILIPSFWM6000
Lowering the volume aloneFan doesn't fireIn my case, it was the damaged fan drive transistorStiltec
PHILIPS 32/42PFL3007D/78
Hdmi doesn't workRegulator u701 with 4.2 volt output. I changed it and the output went to 3.3. I was lucky I didn't burn the HDMI ci.Before changing the HDMI IC, check its supply voltages.RDS
PHILIPSAS 405
Power led does not lightJust give it a touchFredy
PHILIPS43PFL3707D/78
Shutting down, it crashed on startupRegulator u701 g1084-33tu3uf, 3v3 regulator varying voltage between 3v6 and 3v7Replace the regulator and add the c719 220μF 16v, go for the hugValdecir Schena
PHILIPS 32PFL3606
Resistor next to the indication k1 with a value of 750k/smdYou are giving tips without even checking the model, this solution described is for model 32pfl3605 and it does not work for 32pfl3606, pay more attention to what is posted without checking the correct model guys
PHILIPS FW-C505
I'm sound7501 tda 7468d ruimTo replaceAdriano
PHILIPS50PUG6513/78
50PUG6513/78
Does not turn on, no standby.Shorted mosfets and blown ceramic capacitorPower supply board 715g8967-p02-009-001s with the power supply board fuse open (5a-250v) replace but first replace the 02 mosfets q9102 and q9101 (k10a50d) and the 02 ceramic capacitors that sit on top of them 101k 1kvMARCO BORSATO - MEDTEC INFORMATICA
PHILIPS47PFL4007G-78
Turns on in a few seconds turns off to turn on again you have to wait a whileAltered or faulty 3.3v regulator u701 g1084 -33
PHILIPS 14PT3131
Turns on and when the image appears, it turns offResistors 3443 and 3444 of 1r presenting 6r eachReplaceEliel Magno
PHILIPS 14PT3131
Turns on and when the image appears, it turns offResistors 3443 and 3444 of 1r presenting 6r eachReplaceEliel Magno
PHILIPS 14PT3131
Turns on and when the image appears, it turns offResistors 3443 and 3444 of 1r presenting 6r eachReplaceEliel Magno
PHILIPS40PFH4100/18
TPN15.1 ELA
The STBY LED turns on and does nothing else.No reset voltage.Substituir o ic u410 na main board.jose almeida tavares