Search: SEMP
Results: 2824

SEMP Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
SEMPTV1452AV
With normal image and without audioC613 sound output filterReplace and run for the hug!arnaldo(Eletroequipsom)
TCL SEMP50P65US
How to reduce the current of ledsChange the 10k smd resistor r613 for another 330k resistor I put 470k this resistor is close to the ICbadri eletronica <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
SEMPLC4046FDA
The TV turns on and has sound, lights come on but no image.Short t plate com.Shorted or leaking smd capacitors, c11 and c12 t board with.RNSPTEC
SEMP TOSHIBA55L5400
Tsound are times when it turns on and tsound are times when the logo just appears and goes back to standbyN805 3.3 volt regulator was only at 3 volts and tsound were times when it was normalBarter itCentral EletrĂ´nica
SEMPTV 1033LACDC U 16
Vertical closed and without soundDoesn't work
SEMPTV2134
SK11
Tsound is sound in AV and tsound is no sound in RFIc801 la72703ReplaceEletroClaudioPE
SEMP2134
SK11
Turns on and off by itself.C635 (330uf/50v) seco.Replace c635.MARCONES DE ARARIPINA-PE.
SEMPTV2090I
U14
TV with flickering image, white stripes appearing, shaking for hours and then starting againLeaky 7805 voltage regulatorChanging the voltage regulator 7805ELETRONICA KLEIN
SEMP TOSHIBALC3255 A WDA
The image is flashing, the backlight is flashing, if you notice the problem it will be due to the low 12v voltage.In my case it was the v806 next to the 12v connector on the main board, it is npn and was open, just compare it with the ones next to it, they are the same reference.fabiusmax
SEMPTV2134BSL
SK11
With the letter m in the corner of the screenEnter service mode by clicking menu on the remote, then 1 and 9, and pressing the 100 key on the remoteEnter service mode by clicking menu on the remote, then 1 and 9, and pressing the 100 key on the remotedj pituka
SEMPTV2934
Retraction lines and rainbowD304-flashingReplace without measuringWHATS 18997043159 MARCELO
SEMPTV2134BSL
SK11
Turns on and off, closes horizontally and turns off and then turns on again, change cap c613, 102, it keeps getting hotChange cap c613, 102, in the primary of the power supply next to the strwdj pituka
SEMP TOSHIBALC4045
LC4045F
TV turns on without backlight. At first I thought it was an inverter boardBurnt out bulb causing backlight protectionChanging the lampsStefanon
SEMP1454
SL
Alloy has sound but the flyback does not generate anythingI'm goingI just replaced it and the TV started working againEdval
SEMPTV2134BSL
SK11
Alloy with vertical lines at the top of the screen, as if it were that 100uf cap.Change resistor r333, 220rdj pituka
SEMP TOSCHIBA43L2500
SEMP
League without image buses ok oz9902cgn entering protectionPut a 15k resistor on pin 8 and the ground works perfectlyMijail eletrĂ´nica alternativa
SEMPLC4046FDA
It doesn't turn on anything or stand by. inoperative.F901 open, qw901 and qw902 shorted.Qw 901 and qw 902 are f13nk50z / I put ( p14nk50zfp ) in place and it was great. save * ( rma tips )* subscribe tsound and leave your like.Romulo rma dicas
SEMP TOSHIBADL3244(A)
White screen without image with soundCapacitor shorted on the screen board. watch the video https://youtu.be/wxlzi_djyxsEliel Batista
SEMP TOSHIBAV2 48L2400
Backlight turns on and turns off in a few secondsDeactivation of backlight protection. on the inverter part of the main board, go to ci n701 and place a 100k resistor from pin 10 to r786 (it's just below the ci). By doing this, backlight protection will be deactivated.EC
SEMPTV 1492
U16
Very low or no soundChanging the cap. electrolytic c613Alexandre Batista