Samsung TV Repair: Common Faults and Solutions.
Search: Samsung
Results: 3814
Results: 3814
Samsung Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SAMSUNG | PL51E490 | Flashing standby, does not turn on | Big blue pcs801 capacitor with cold soldering | ELETRÔNICA JAMBEIRO | |
SAMSUNG | LN32C350D1M | Main board voltages pulsing and stand by LED on | Heat the ic203 (aoz1031). If it stabilizes and the TV works, change the ci. | Eletrônica Cecé, Brumadinho MG | |
SAMSUNG | UN40ES6150 BN44-00502A BN44-00502A | TV turns on, off and stays on stand-by | Check on psu (bn44-00502a) dm855. | Replace diode and check for cold solders | José Félix |
SAMSUNG | UN43AU7700G | Writer | Infinite loop | Remove the infinite loop | Nelson Marinho |
SAMSUNG | PL42A450P1XZD | The relay hits when it turns on and after a few minutes the TV turns on | Change without measuring cq815-845 and 806 in power supply bn44-00206a | SANTOMEL | |
SAMSUNG | LN26A330J1 | Standby and beep only. | Power supply board did not release voltages correctly. | No bad components were found, I cleaned it with soap and water, after drying some bad tracks appeared, I made the repairs and the TV worked perfectly. | Eduardo Schmidt |
SAMSUNG | PL42A450P1XZD | Hitting relay | Capacitor cs823 47/100v 105º power supply bn44-00206a | Replace without measuring | SANTOMEL |
SAMSUNG | UN50RU7100 | Restarting (screen symptom) | Check c99 to c104 vcon | Junior - Tecnoprom | |
SAMSUNG | UN32FH5203G | Does not turn on, standby on | Short in the 5v line on the main board | Ic201 shorted on the main board, replace it. | NiloTech |
SAMSUNG | LB40B530 | Turns on normally after turning off the backlight | Weak lamps, with darkened cathode | ALDEIATEC | |
SAMSUNG | PL43F4000 | Turns on has sound and video, but turns off. | Welds with poor contact and especially in cs809s, redo the welds at the power supply. | Ademir tc | |
SAMSUNG | QN50Q60 | Blue screen, restarting | The defect was in the v-com on the right side, I isolated some tracks of the flat that made the connection between the plates and the image returned to normal | ||
SAMSUNG | UN40J5200 BN41-02307 | TV won't turn on main board | Replacement of the synchronous voltage regulator ic206 and the open fuse f202 on the main board | Replace regulator and fuse | marcos moreira |
SAMSUNG | UN40J5200 L40MSF_FHS | TV doesn't turn on | Change mosfet qm803, dm855c and dm861c the same, it's shorted | Replace the mosfet and diodes | marcos moreira |
SAMSUNG | UN48H4203AG | TV didn't turn on, just stand by blinking a few times | Cm823 leg cut/corroded, ceramic capacitors leg burst | Replace or adjust | Decio Polita |
SAMSUNG | UN40F5500AG | Does not turn on, just flashing standby (no backlight) | Without 13v power supply changed 10r resistor was measuring 4.22k next to the pfc capacitor | Replaced capacitor 10r fiz um video video... | Jean Vinicius Franco Lorenz |
SAMSUNG | UN50TU7000G | Backlight off | Poor contact in the power supply board connector, | A direct connection was made from the power supply connector with wire to the LED bar connector, everything was fine | Fernando técnico |
SAMSUNG | UN43J5290 | Won't turn on (dead), AC fuse open | Curto mosfets qm801cs e qm802cs (50r380) | Replace the mosfets and the 5a fuse and run to the hug | World TV - Sorocaba |
SAMSUNG | LN40C530F1M | Stand-by LED is on, when you press power nothing happens. normal voltages of 13v b and 5v a and b. However, voltages b turn on and off while a remains stable | Ci hdmi (ic 1101) shorted or with faults preventing the TV from starting and triggering main board protection | Remove the CI and test the board again on the TV, if it works, replace the CI with a new one | Eletronica SV - Guaira PR |
SAMSUNG | UN48J6300 | The backlight does not come on, nor does it blink after replacing the complete LED panel, in addition to a defect in the LEDs, also in the power supply, probably the panel and LEDs caused an overload due to a short in one of the LEDs and the power supply failed. | I.c position ic9101 (7014x / 1449) smd in the secondary of the power supply, it switches the 02 fets that feed the LEDs and also the position transistor qm885 | I replaced it because I had scrap, but I don't know the correct nomenclature, without time to open a schematic. interesting in this project, because although the power supplies come out separately from the connector that goes to the LEDs, in fact in the power supply itself if you observe the rulers go in series from to to apr, tsound are 03 pairs of rulers... that is, 02 + 02 + 02 in series. | MIGUELTV |