Semp TV Repair: Common Faults and Solutions.
Search: Semp
Results: 2824
Results: 2824
Semp Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SEMP | TVC-166 | Normal image just has no characters on the screen and the functions work normally @@@ | I have it from memory ica01=47c434n3528 | Help yourself, leave your tip ass. arni | EETRONICA ARNI-L. LEAL- SC |
| SEMP | TV-1022E/1480E/2080E | No contrast | Ca66 with leak | carlaosbc | |
| SEMP | TV1030 | Vertical closing | Bad contact on the q430 emitter | Scrape the board and solder. | Evandro Estrela |
| SEMP | TV.2016 U18 | Turns on normally after about 10 to 15 minutes it starts to hiss at the power supply and the screen starts closing and turns off | The cause was a ceramic capacitor giving a small leak vlw | C865. its value is 103 | luis carlos |
| SEMP | TV2934SKY SK-91 | Dark screen with no image and no sound, and flickering | Q606 | Replace | EletroClaudio Aguas Belas |
| SEMP | TV2934BL SK11 | Replace | C311 47/200v exhausted | Replace | paulo-maceio/al |
| SEMP | SD-3020VK | DVD completely inoperative (does not turn on) | Dodo 1n4002 (d 18) | The replace of the same | saulo figueiredo |
| SEMP (TOSHIBA) | 2134 | When turning on the screen with excessive brightness | Change cap 4.7/250 voltage 180v rgb | Francisco | |
| SEMP TOSHIBA | TVC 147 | Low power supply with hum. | Dz810 shorted. | Gilcimar Rocha Pereira | |
| SEMP | TV 1484 FAV U11 | When the volume increases, the image becomes shaky, turning horizontally and vertically at low volume, it normalizes. | Change electrolytics near the sound system. | JN ELET.NEVES 100% LEÃO... | |
| SEMP | SD4071U | Does not read any type of media (CD or DVD), or does not spin the disc. | Transistor s8050 which is between the transistors s8550 | After checking: engine, driver, flat and optical unit. replace without testing the only transistor s8050 | Eletrônica Áudio e Vídeo |
| SEMP | SDRX38D | When turning on, it just stays on the home screen and hangs | The 3.3v 0.3a regulator (u18a) on the IDE drive board shorts out. rip it out and place a 1a regulator on the other side of this board (u18, in place of the lime green sticker), eliminate the jumper (0Ω ar2) from the regulator output to ground and place a 100r resistor in its place. This regulator is a little difficult to find, so you can use an old computer CD drive. | Ronie Grein | |
| SEMP | C29LH43B | Vertical closed | D476 | Component poorly soldered at the factory, cold soldering over time, also check r476, pin 3 of the flyback | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| SEMP | FS TUNING CI TB1231AN | Vertical closed, squeaking sound. look at the whole area of the vert. ok. look at dz830, dz421. | They are between the ci and the s.vertical. | ELET.JN NEVES Ce | |
| SEMP TOSHIBA | 1495 RM U15 | Faulty primary power supply | Doesn't start | Open fuse-r3r3 open7w-str w5753 replaced-dz876 5v6 with leak and r smd 876 220 replaced | Manoel Fernando |
| SEMP | TVC-10IL | No color | Potentiometer r520 | After checking the chroma burst, I got the r520 open and just replaced it and the colors came back | Bruno Capozzoli |
| SEMP | TV2134 | Dark screen (no weave) | C409(394j/250volt)poliester | Replace it without testing | Jarbas Santos (Eletro-serv) |
| SEMP | TV2134 | Half moon side edges | Q303(flake) | Replace it without testing | Jarbas Santos (Eletro-serv) |
| SEMP | TVV2134 | Half moon side edges | Q303(flake) | Replace it without testing | Jarbas Santos (Eletro-serv) |
| SEMP | TV2134 | Side edges | Q409 (with leak) | Replace it without testing | Jarbas (ELETRO-SERV) |