Semp TV Repair: Common Faults and Solutions.
Search: Semp
Results: 2824
Results: 2824
Semp Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SEMP | TV2066 U7 | When it heats up vertically fully closed 8817 maria do andré/ | After checking the entire vertical, the defect was in the ceramic capacitor c304 1500 with low capacitance, this capacitor killed the 4v that feeds the vertical, it is connected to pin 54 of the microphone tb1229an | Tracar c 304 1500 | marcos melo cascavel ceara |
| SEMP | TV2091KAV U15 | Dull | Replace capacitor do screem c902 | Replace without testing | marcondes, OHM eletronica Jaicos-PI |
| SEMP | SD-5090VK PROCSS.ZORAN | Doesn't start | Eeprom u105 24c08 | Secondary power supply between 10/12v, standby on, when turned on the LED goes out and does not arm, just replace the eeprom u105 24c08/24c04 | PALAURO |
| SEMP | TV1490 U14 | LED lights up, but doesn't turn on | C887 de 100mf/50v | Barter it | marcondes, OHM eletronica Jaicos-PI |
| SEMP | TV2082E U7 | Vertical fully closed 8817 maria do andrer | After checking the entire vertical, the defect was in the processor, I removed it and cleaned it, returning it to normal vertical operation. | Clean the microprocessor, check the 4.25 v on pin 54 on the micro | marcos melo cascavel ceara |
| SEMP | TV2987EMS LEM2 F-74/379E | Turns on right after turns off | I changed the capacitor c 448 33uf150v and it didn't turn off anymore, I hope it can help someone, thank you. | gelson eletronica | |
| SEMP | TV2982 LEM9 | Starts and cuts, leaving the LED off and +b with + or - 30v. | Changed resistor r886: note (measure with digital test) | Replace r 886 | GEORGE PONTES |
| SEMP | TVC102 | Out of horizontal frequency (annoying buzzing) and closes the frame | Change c408 next to the computer | Moraes SPTV Campinas | |
| SEMP | TVC102 | Escapes fine tuning | Replace ceramic capacitor c822 power supply board | Moraes SPTV Campinas | |
| SEMP | TV 1484 U11 D2 | Power supply pulsing +b with low value and oscillating | C 810 220/385v I changed it and solved the problem | Paulo. | |
| SEMP | TV 1452 U19 | When turned on, the LED turns on and off quickly, the power supply does not start, +b low. | Strw 5453c, I put a, it worked. | Manoel | |
| SEMP | TV2084 U13 | Overheating 880 and 881 killing 9v voltage | Varicap e r880 e 881 | Replace them | marcondes, OHM eletronica Jaicos-PI |
| SEMP | TV | Hang up | |||
| SEMP | 2084 U13 | Blue screen, low sound | I replaced the q612 2sa1015 external pci spot | ||
| SEMP | TV 1451 NAV | Weak oscillating, white screen and reduced on the sides | 5v missing for one of the micro stages | Q 841 | Manoel |
| SEMP | TV1470E | Closing the bottom part of the image | C317 de 1mf/50v | Barter it | This email address is being protected from spambots. You need JavaScript enabled to view it. Marcondes Jaicós-PI Ohm eletronica |
| SEMP | TV2122 O FS U19 | Negative image | Q109 leaky video transistor | GILSCE | |
| SEMP | TV2987FMS | Dark screen | C902 do screem | marcondes, OHM eletronica Jaicos-PI | |
| SEMP TOSHIBA | TV 2159 U18 | Piscando stand by | D885 | marcondes, OHM eletronica Jaicos-PI | |
| SEMP TOSHIBA | TV2090 U14 | Fixed vertically; open lines at the top of the tube | Ic421 ;reg of 5v | MACCELETRONICA |