Semp TV Repair: Common Faults and Solutions.
Search: Semp
Results: 2824
Results: 2824
Semp Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SEMP | LC3246WDA | TV works for a while and turns off, leaving the green LED on and won't turn on again | At the power supply in the primary, check the zener diodes zdw901-- 16v and the diode dw905 --1n4148 with leakage | The dw905 1n4148 was replaced and resolved | Eletrônica Ômega |
SEMP | DL4844AF | TV turns on and off the LEDs, green STBY light | I changed r766, inserted r776(4k7), removed 1r0 from each isense, it kept turning off. | Test LED bars with an external power supply, the good ones light up at 25vdc, each one, the bad ones above 35vdc (do not use them) | jjsantosneto |
SEMP | L39S3900FS | Does not light LED bars | Shorted capacitor on line +b pin 2 of ci ocp8121 burns r804 10r | AGNALDO | |
SEMP | 32RV700(A) | Turns on relay gun standby LED turns on and off and TV doesn't turn on. power supply with voltages, everything is normal. | Main board does not light up the signal indicator LED. | I replaced the main board and the TV started working normally again. | George Pontes |
SEMP TOSHIBA | 2134(C)SL | Turns on normally then turns off. turns it on again, turns it off sometimes until it stays on | Q706 transistor s8050 (with leakage it heats up) | Q606 transistor s8050 (with leakage it heats up) | Fernando Nascimento |
SEMP | 2934 SK91 | Burning exit h | C 307 7n6 open | EletroFenix | |
SEMP | TV 2134 (C) SL | Arming the relay and disarming it by entering protection | 2.2k resistor changed to 27k | (r604) close to the photo coupler | Eletrônica Basstos |
SEMP | LC3246AWDA 9209 | After turning on the power button, the TV turns on normally but turns off the lights in 3 seconds | Changed lamps | Solution: remove d705 and d706, leave without, and go for the hug | Eletronilo |
SEMP | LC3246AWDA 9209 | After turning on the power button, the TV turns on normally but turns off the lights in 3 seconds | Changed lamps | Solution: remove d705 and d706, leave without, and go for the hug | Eletronilo |
SEMP | 2134 (C)SL SK11 | This TV turned on normally after a few minutes, the image was duplicated with several scratches on the screen and it also made a strange noise next to the flyback | L302 detail so you know if this coil is really bad, just put a magnetized screwdriver if it normalizes, just change it and run for the hug | Eletrônica Lima pb | |
SEMP TOSHIBA | 40L2400 | TV turns on normally after a while and turns off. | Altered 3.3 regulator. | Swap n805 | Eletrônica Ideal |
SEMP | 2934 SK91 | Connects with the weak image as if it were the image tube. I changed the tube but it wasn't the image tube! | L301 | Replace the l301 790μH coil without measuring and just run for a hug! | Sinailson furtado |
SEMP | 2934 SK91 | Connects with the weak image as if it were the image tube. I changed the tube but it wasn't the image tube! | L301 | Replace the l301 coil without measuring and just run for a hug! | Sinailson furtado |
SEMP | TV2134 SK11 | Sound goes back and forth, increases and decreases | C636 | C636 exhausted by another is good again | Marqueis eltec eletrônico |
SEMP TOSHIBA | DL3254(A)W | Back light on, but no image | Capacitor incurto | Replace cp17 | Eletrônica Ideal |
SEMP TOSHIBA | LC4055FDA | LED turns on and off, when it heats up it works. | Cb904 | <small>electronicssupplyparts</small> Gramado/RS | |
SEMP | TV2159 OFS U18 | Does not turn on, with 56v on the secondary power supply | Replace zener diode d862 and d863, both 20v. | DJ PITUKA | |
SEMP | 1452 U19 | Turns on and in a few minutes turns off by itself | Cold solder on the main board and crt board. | Redo all the cold soldering, especially in the 5v supply regulators sector and in the cables that go from the main PCI board to the tube PCI. | 2200uf/16v |
SEMP TOSHIBA | TV1484FAV U11 | Vertical closed | Replace without measuring c305 and c306 | jr_TEC | |
SEMP TOSHIBA | 40L2400 | When I connected the plug to the electrical network, the standbay LED would light up and go out quickly. | An LED bar with a shorted LED | I replaced the LED and the function |