Sony TV Repair: Common Faults and Solutions.
Search: Sony
Results: 20059
Results: 20059
Sony Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | KDL-40EX720 | Hdmi doesn't work | Replace sil9287b | ||
SONY | MHC-X66 | Goes into protection when lifting the volume | Cooler | Replace the same | barbadinha |
SONY | KLV-37NL14A | Error code 6 blinks (backlight) | Check inverter_error line capacitors (3v3), look at q4014 | Lexus | |
SONY | KLD-46Z410 | Turns on std by, but then turns it off, a loud beep at the power supply. | In the power supply it has 3 trimpot, in my case the defective one was a 22k changed in the power supply | I immediately replaced all the trimpots, placed SMD resistors under the power supply board, it was great. | Alex Lopes This email address is being protected from spambots. You need JavaScript enabled to view it. |
SONY | HCD-EX66 | Does not turn on, power supply does not oscillate capacitor remains charged | D930 30v | Anderson | |
SONY | FH-B1200 | Deck does not drive main engine | Open resistor r306, replace resistor, 5r6 | ||
SONY | KDL-46W805A | Doesn't start | 3.3v varying | Ci 6301 faulty (power supply primary) | Maurilio |
SONY | KV-29T80 | The power turns on, tsound is no brightness, the LED flashes twice in a cycle, | Disco capacitor c601, 1k5 by 2kv at power supply | Replace the c601 for another 1k5 by 2kv | CLÓVIS |
SONY | KDL-46NX705 AZ1-H | The TV turns on and appears immediately after the 6th blink, it looked like the LEDs but not | Smd fuse power supply board position ps6800 0.5a | jucier | |
SONY | KDL-32EX525 | Turns on backlight with low brightness. | Photocoupler ph6304 with leakage did not stabilize output voltages +150v and -150v. | Replacing the ph6304 photocoupler | Eletrofepar |
SONY | KDL-32R305B | Does not turn on, the LED flashes 6 times | It is necessary to inhibit backlight protection | Place a 10k resistor (pin 31 of the backlight ci - bd9397efv) to ground. | Dennys Gross |
SONY | MHC-EX8 | Protect, direct protection when plugged into the socket | Capacitor c600 shorted, interfering with the 9volt reg ic690 | Replace do capacitor c600 100μF x 16volts | Tralli |
SONY | KDL-46R475A | TV completely inoperative, won't turn on. | Tsound was only a voltage of 3.3v on the main board (stand-by), with no voltage on the other regulator ICs. | Replace transistor q701 (ao4421 smd) on the main board. This transistor powers the u703 regulator. | Ferrarini |
SONY | HCD-GTR66 | When turning on the device, the stand-by LED flashed. | Smd transistor q1307 in the thermal protection circuit, replacement solved the problem. | EduSSantoz | |
SONY | HCD-GTX878 | Sound off the panel characters | It was a simple zeni diode d1291, it is located in the part of the power supply, guys, then make a sound on the components of the power supply square | NANDO ELETRONICO DE SAOJO DO ARRAIL PIAUI | |
SONY | HCD-GTX878 | Sound off the panel characters | It was a simple zeni diode d1291, it is located in the part of the power supply, guys, then make a sound on the components of the power supply square | NANDO ELETRONICO DE SAOJO DO ARRAIL PIAUI | |
SONY | KDL-32BX425 | When the logo appears, the TV turns off and the red LED flashes 3 times | 3v3 regulator u114 I put a 3v3 1117, grounding pin 1. | Davi.sls | |
SONY | HCD-GTR33 | Does not tune in to the radio | Turn on, press the keys: enter/stop/stand by at the same time | reginaldo moronte, eletronica junior caldas novas | |
SONY | KLV-40M400A | TV does not turn on, relay activates and disarms then, red STBY LED flashes 4x and repeats. | After setting up the power supply on the bench and all the voltages appeared. but when connecting the main board it killed the 12v voltage. | SMD ceramic capacitor shorted to ground on the 12v line connected to pin 3 of the IC4051. I removed it and the TV started working again. | Jeferson |
SONY | DSX-A100U | Usb overload | Ic 1304 with problem, remove and jam pins 1 and 6, it is on the right side of the coil and has 6 pins | Rodrigo cofferi |