Sony TV Repair: Common Faults and Solutions.
Search: Sony
Results: 20059
Results: 20059
Sony Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | HCD-EX6 | When I plugged the sound into the socket it would turn on and off, only the times I turned it on, neither the CD nor the USB would work. | After analysis I found the diode d400 1n4002-a2 which is on the panel PCI it was open, after replacing the sound it works normally again. | Jonas | |
SONY | HCD-EX6 | Turned off in 3 seconds | Defect in the CD part, when I disconnected the flat cables it stopped turning off | Jonas | |
SONY | HCD-EC59 | Protect | Q619- main power on-off | Replace q619--2sc3052f | EMERSON RIBEIRO |
SONY | HCD-SH2000 | No sound/Audio, does not arm protection/protect, displays please wait when activating USB or CD. | Tsound is no 9V power supply for the IC500 audio processor or the 4558 preamps. | Transistor q800 and c754 short, resolved by replacing them. | EduSSantoz |
SONY | HCD-GTX88 | Does not come out of standby | X402 bad 5mhz crystal, just change it (it was measuring around 2.065 k from one end to the other, that is, leaky). | Ronaldo Vieira | |
SONY | KDL40BX455 | TV turns on red LED lights up turns green and turns back to red and flashes | R 9810.... 9811... 9812 remove and scrape the glue underneath | RJ ELETRONICA | |
SONY | KDL40BX455 | TV turns on red LED lights up turns green and turns back to red and flashes | R 9810.... 9811... 9812 remove and scrape the glue underneath | RJ ELETRONICA | |
SONY | KLV-40S200A | When turning on the TV, the LED flashes 4 times, no image, no sound. | Replacement of fuse f401 - 10a on the inverter board on the left side of the TV | Replacing the fuse on the inverter left upper board f401 10a | Ferrarini |
SONY | KDL-55W805C | Turns on, the back light comes on, the Sony logo appears, then turns off and the stand by LED flashes 3 times | Shorted smd capacitor next to the ic 8000 close to the cn8001 connector | Replace it or leave it without a capacitor | Alex Lopes <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> |
SONY | 40EX455 | Sony appears and turns off | See q6101, q6102 and r6536 and this electrolytic capacitor on the 5 v line c9305 | ADAILTON | |
SONY | 40EX455 | Sony appears and turns off | I replaced all the photocouplers and resoldered all the cis smd and it solved the problem. | FERNANDES | |
SONY | KDL-40HX755 | TV flashes red LED but not in the image, the TV is on if you loosen the tcon cable it doesn't turn on it only flashes LED 5x saying tcon error | Changing tcon didn't work, on the main board tsound are some 4 in 4 coils right in the connector that goes to t com. one had broken.. I made a jump and it turned on ^_^ | Alexandre | |
SONY | KV140-MG | Doesn't start | Q602 and q603 in the power supply shorted. | Replace q602 and q603 (2sc4834) | MARCONES DE ARARIPINA-PE |
SONY | MHC-GRX9900 | Display lights up very weakly | All micro and display voltages are correct | SebastiĆ£o | |
SONY | MHC-GTR6 GTR8H | Turns off and LED flashes | Fault on the thermal detect d1310(maz8091) dz9.1v line, you can put dz10v. | samuel leite | |
SONY | DZ-295 | Does not turn on display off power supply ok and display too | Lack of voltage ever 3.3 =e3.3v | Look for the diode d503 it receives 4v and releases 3.3 I replaced it and the problem was resolved. | FLIPFLOP |
SONY | HCD-EX660Z | Goes into protection after a few seconds | Solution is to change the sound output IC | Replace the sound output, remove it from the power supply and you can hear the sound on the headphone input directly from the pre | |
SONY | KLV-37NL14A | Turns on and then turns off by flashing red LED 6 times | In my case it was a fuse on the reverse board, position f1, close to the middle screw | Note: this TV has two versions. the invert plate for this is "fr-4-86-py" | Mario Moreci |
SONY | KDL32R305 | It turns on, then makes noise and turns off and flashes 6 times, after changing the LED bars it was the same thing, because when changing new bars you have to solder the bar fittings as they give very poor contact and represent a defect on the board | Weld bars one by one into the fittings | LORD | |
SONY | KLV-32S300A WAX3 | Negative image / inverted colors | U8 as34-g on t-com board [it is a 14-pin integrated (7+7)] | I used an el5420crz from another t-with scrap | Baguatech |