Sony TV Repair: Common Faults and Solutions.
Search: Sony
Results: 20059
Results: 20059
Sony Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | STRV55 | Wire numbers are reversed | Incorrect wire number. numbers #1 and #3 reversed. | ||
SONY | STRV35 | Defective outputs | The npn output transistor opened on one channel of each of these receivers. no other problems found. | ||
SONY | STRV2 | P/n for glass | Cases of concealed damage to front glass on these models havebeen reported. present solution is to replace entire front panel assemblybut it is costly. -hq comments: a similar situation developed on the str-4800sd, -5800sd,-6800sd models 3 years ago. | ||
SONY | STR7065 | Protection transistors reversed | Burned main amplifier board was replaced (x-482-232-50).amplifier clipped at 1 watt out. | ||
SONY | STR212 | Defective ic20, 301, q301, 302 | No am or fm - ic201 voltages incorrect, q301 collector read 11volts. replacement of individual ic, would knock the other chip out. | ||
SONY | STC7000 | Adjustment needed | The maximum deflection on tuner input meter did not correspondto center channel on tuning meter. adjustment of fm discriminator and fmif was unsuccessful. | ||
SONY | SQA2030 | Defective q701 | Noise in back channel outputs. -hq comments: replaced regulator transistor q701, 2sc1124. | ||
SONY | PSX70 | Weak motor | Tone arm would not complete return and play cycle wouldstop widway most times. | ||
SONY | PSX40 | Defective mgh | Turntable speed erratic. maximum output from mgh was 15-20mvp-p. even slight readjustment of the head caused it to scrape theplatter. | ||
SONY | PSX30 | Loose lead on c101 | Frequent slowing down of motor. found one lead of c101loose. | ||
SONY | PSX30 | Defective detection lever | Scraping noise. cause: detection lever had been jammed underprotrusion on bottom of cam gear in shipping and was permanently warped.this was touching the top of the magnet ass'y on the motor shaft. | ||
SONY | PSX20 | Defective ic101 | In play mode turntable operates normally, in stop mode (poweron) turntable rotates backwards. in stop mode, ic102-2 output goesnegative 2.1v and inverting input remains slightly positive (pin 6). theoutput of logic pin 6 of ic101 remains at +1 volt. g | ||
SONY | PSX7 | Defective q203 | Automatic function engages when power is turned on or off, andspeed varies. this only occurs when unit is cold. | ||
SONY | PSX7 | Replacement motor will not mount | During troubleshooting, we found that replacement motor(a-460-801-9a) would not mount properly. dimensions of motor shaft andspindle were different. | ||
SONY | PSX6 | Open cap c205 | After several minutes of operation platter slows down and getsprogressively slower. | ||
SONY | PST25 | Spacers to remove | Platter scrapes on side opposite tonearm. | ||
SONY | PS212 | Leaky q3 | Turntable speed is too fast. | ||
SONY | PS20F | Replacing stylus | The stylus of the moving coil cartridge for the ps-20f isreplaceable. the part number is nd206. | ||
SONY | MDR3L2 | Wires break | The distributor (norcal) has reported to me several brokenwires on these units. the wires break at the plug end. | ||
SONY | M200 | Spring out of location | Switch sw3 did not move to off position when stop buttonengaged. problem was spring (3-561-626-00) was off at stud end, not slideend. |