TV Repair: Common Faults and Solutions.
Search:
Results: 87440
Results: 87440
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | XR6200 | Excessive flutter | Excessive flutter in one or both directions. found loosescrews that hold bracket assembly in place. | ||
SONY | AVK715M | Color code on cable is wrong | Video input has a yellow band on it to distinguish it fromthe audio input. these two inputs are reversed. audio input is the onewith the yellow band. -hq comments: because some non-sony tvs employ the reverse l shape typestereo mini plug, the yellow b | ||
SONY | KV27XBR10 | Singing yoke, replaced yoke, see service bulletin 114 | Loud singing noise from yoke | ||
SONY | CCDTR5 | Unit loads half way/drum fails to change direction/unloads | Pin 64 of ic-601 would not go h for the proper duration oftime when loading. if you stop the drum with your finger, when thedirection change was supposed to occur the unit will load. | ||
SONY | WMAF57 | Engaging of play button | Due to the mounting of the pcb, the play switch becomesdifficult to engage. | ||
SONY | WMAF50 | Engaging of play button | Due to the mounting of the pcb, the play switch becomes difficult to engage. | ||
SONY | WMAF48 | Engaging of play button | Due to the mounting of the pcb, the play switch becomesdifficult to engage. | ||
SONY | WMA26 | Engaging of play button | Due to the mounting of the pcb, the play switch becomesdifficult to engage. | ||
SONY | RMX2 | Power harness schematic is wrong | Page 8 of the s/m shows cn-801 as a 9 pin connector, but theharness is shown as only having 4 wires. page 10 of the service manualshows all nine pins being used. the installation manual shows actualcolor code which is correct. -hq comments: the instal | ||
SONY | CCDV5000 | No eject/tape jam | Tape jam and no eject. | ||
SONY | MPKF40 | Models compatible with the mpk-f40 | Which models will fit in the mpk-f40? | ||
SONY | MPKV11 | Modifications for use with ccd-v99 | Some mpk-v11s do not accommodate the ccd-v99. | ||
SONY | GVM2000 | Support bracket part number (a board) | Support bracket for the a board on the gvm-2000 is needed.no part number is listed for this item in the service manual. -hq comments: the part number for this item is 4-393-914-02. pleaseupdate your service manual. | ||
SONY | KV27XBR50 | Part number for power switch is wrong, 1-571-532-21 | Part number for the power switch is incorrect in servicemanual. -hq comments: the correct part number is 1-571-532-21. please make theappropriate corrections to your manual. | ||
SONY | SL2700 | Part number for cassette in switches | On page 169 of the service manual, there is no partnumber for the cassette in micro switches (next to items 370 and 371). | ||
SONY | SPPS10 | No handshake between base and handset | Intermittent no handshaking between handset and base. when acadaptor input is shaken, sometimes unit works. | ||
SONY | CCDF55 | E - shutter does not change speed in manual mode | Shutter speed is fixed at 1/60 or 1/100 second, and cannot be changed with the shutter select button. | ||
SONY | CCDV5000 | Part number for connector cn604 - cn301 | We need the part number for the following connector. -to tokyo: can you give us the part number for the board connectorthat goes between the di-21 board cn-604 and the vc-55 board cn-301?it is a four-pin 1.5mm pitch. thank you in advance. -hq comments | ||
SONY | CCDTR5 | Caution light flashes when tape ends in play,ff of rew modes | In vtr mode when the tape ends in play, fast forward or rewind modes, the caution light flashes. | ||
SONY | WMAF54 | Weak or defective tuning knobs | The tuning knob is very weak, and breaks easily or falls off. |