TV Repair: Common Faults and Solutions.
Search:
Results: 87436
Results: 87436
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | KPR41DS2 | Spots on screen, see tv service bulletin # 17 | There were spots on the screen, one big one toward the bottomright hand portion of the screen. took screens apart and found fine dustparticles. with a fine brush i was able to clean both screens. with thescreens rubbing together in shipping, there mus | ||
SONY | STRAV910 | Wrong part number for 6 pin output jacks j403-j405 | The part number listed in the manual for the output jacks areall the same regardless if it is a 4 pin or 6 pin jack. | ||
SONY | KV8AD10 | No power | No horizontal drive. | ||
SONY | KV32SXR10 | Two inch border around picture, leaky q-1560 and d-1502 | Unit had a two inch border around picture. | ||
SONY | CCDTR5 | Camera will not load | Camera will not load. this is the second camera with this. | ||
SONY | GV8 | Record knob | Record knob is not available. it is necessary to order entirepanel items yet the power knob, which is almost the same is available,items 12 and 10. | ||
SONY | XR7180 | Unit appears dead | The unit appears to be dead but does have some leds on. some of the supplies are low. this is due to an open emitter-base junction of-317. leakage through r-363 makes the circuit look loaded down. | ||
SONY | TCWR510 | Wrong part number | Part number for q-701 is not in the kansas city parts system. | ||
SONY | KV25XBR | Schematic error regarding v-pulse | From connector a-2 pin 3 on the v-pulse does not correctlyfind its way to ic-103/pin 4. after being inverted at q-127, its showngoing to ic-103 pin 15, fm trap pin 4 is shown tied to power switch line. -hq comments: thank you very much for your report. | ||
SONY | FD500 | No raster - audio ok, replaced open c802 | No horizontal pulse at collector of q-802. a horizontal pulsewas present at base of q-802. collector voltage was 9vdc and the basevoltage was -3.4vdc. | ||
SONY | KPR46CX50 | No white balance adj. in sm, see correction -1 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: see correction-1, or use the white balance adjustmentprocedure contained in the kpr-36xbr service manual. | ||
SONY | KPR41DS2 | White balance, refer to correction 2 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: for the white balance adjustment see kpr-41ds2/correction-2 p/n 9-963-993-92. | ||
SONY | KPR41DS1 | White balance adjustment wrong,see correction number 2 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: please see sm correction number 2. | ||
SONY | KPR46CX10 | White balance, see sm correction # 1 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: for the white balance adjustment procedure see kpr-46cx10/correction-1, p/n 9-964-100-91. | ||
SONY | TCS430 | Head wire too thick | Shielded cable from the pc board to the tape head opens on onechannel. wire i have will solve the problem but it is too thick and in-terferes with the mechanism and buttons of unit. not provided with anykind of head wire to solve these problems. is or | ||
SONY | SSM910 | Wrong part number | Ic-501 is listed in the manual incorrectly as 8-729-262-72. -hq comments: the correct part number is 9-991-577-01. | ||
SONY | XK8D | Pcb change: motor, regulator | The motor pcb and the regulator pcb are no longer availablefrom kansas city parts. newer units have a combination type of pcb. | ||
SONY | KV27SXR10 | High pitch sounds, replaced yoke see sb #0114 | High pitch squeal. | ||
SONY | CDXR77 | Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
SONY | SLV70HF | No playback of self-recorded tapes | When playing back a self-recorded tape, a picture can only beseen in the scan modes. pre-recorded tapes playback ok. |