TV Repair: Common Faults and Solutions.
Search:
Results: 87436
Results: 87436
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | CFD5 | Incorrect reference number | Reference number 46 on page 85 should be labeled referencenumber 44 (part number 3-320-247-11). reference number 46 on page 87 iscorrect (part number 3-320-249-01). -hq comments: thank you for the information. i appreciate your effortin pointing this | ||
SONY | WMAF605 | Part number not in manual | Part number left out of service manual. | ||
SONY | KV13TR20 | Crt replacement | This set does not have shield as shown in manual. degaussingcoils mount on metal extensions attached to mounting band on the crt.servicer has two tubes for replacement that do not have the attachmentsfor mounting the degaussing coils. | ||
SONY | EVS900 | Intermittently will not accept tape | Found that the unit would accept all tapes except p6-120s.tape would intermittently hang up on left side. tape did not fully loadonto reel assembly. | ||
SONY | CCDF40 | Incorrect part number of dt-71 board | On page 147 of the ccd-f40 manual, the dt-71 board part numberis listed incorrectly. it is listed as a-7061-127-a. | ||
SONY | KPR46CX10 | No red, crt filament open | Filament open. | ||
SONY | SLHF1000 | Tracking problem, input of one head is low | In playback, unit has noisy video, tracking shift causes noiseto worsen. symptom appears to be a bad head. rf output shows little orno output from one head, the other is o.k. tracking shift causes thelevel to increase on one head and decrease on the o | ||
SONY | XR7150 | No buzzer on xr-7150/7151/7152 | This problem was brought to my attention by a technician fromcosta mesa ssc, r. elliott. regarding this model as a repeat repair formuting of the beep sound. unit was checked and physically the unit doesnot have a buzzer nor does it appear on the schem | ||
SONY | D2 | Missing reference number and part number | On page 22 of the d-2 manual, there is no reference numberfor flex cable, and i could find no mention of it or a part number in theservice manual. -hq comments: there is a service manual correction no. 1 (9-953-376-91)which provides the part and referen | ||
SONY | CCDF50 | The mounting plate for the a/v in/out jacks is unavailable | Is there a part number for the mounting bracket for theaudio/video in/out jacks? -hq comments: the entire pcb must be ordered to obtain this part. | ||
SONY | CCDM8U | Cc-3 board availability | Is the (cc-3) board available? -hq comments: yes, the (cc-3) board is part of the mechanical chassis.the part number is listed in service bulletin number vcr0298 (2/27/87). | ||
SONY | VTX1000R | Noise in picture | Interference in picture caused by frequency beating the video.the higher the channel number, the more intense the noise. | ||
SONY | CDP510 | High noise during play | High pitch noise through audio when playing. the noise couldbe seen coming out of ic-202 (d/a converter), but not going into the d/a.i replaced the d/a and had the same problem. i could also see the noisecoming out the ram. | ||
SONY | KV2783R | Intermittent tuner drift, resolder t-203 connections | Tuner would intermittently drift off channel. heating orcooling circuit yielded no results. | ||
SONY | D55 | Incorrect part number - q411 | The part number listed on page 60 of the service manual is8-729-195-64. this part number does not come up in kansas city parts.found that the part number is incorrect. the correct part number is8-729-159-64. -hq comments: thanks for letting us know. | ||
SONY | KV32HSR10 | Clock gains time, see s/b-87r1 | Clock gains time intermittently. -hq comments: please refer to service bulletin number 87. | ||
SONY | KV1938 | Intermittent tuner drift, resolder if block | Set would intermittently drift off channel. heating andcooling circuit yielded no results. | ||
SONY | KV32XBR15 | No volume control, replaced ic-251 | Unit displayed multiple audio problems. volume on screendisplay operated normally. sound volume was stuck at approximately halfvolume. if a change was made, it would not appear until channels werechanged. have had two other reports of this symptom. | ||
SONY | GV8 | Is the vcvgv8 glass or plastic | Is the vcvgv8 (sunshade) glass or plastic? | ||
SONY | GEN-HFP | Newer cdp | Eddy from eddys electronics claims that he corrects many ofthe skip problems with our new cdp. he heats the plastic retainer for oneof the sled drive gears and bends it. it is bent until there is noclearance between the gear and the retainer. -hq comm |