Repair Tips
Search:
Results 37055
Results 37055
| Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
|---|---|---|---|---|---|
| Sony | FE-1 | No sound | This may be remedied by entering TT24 in the service mode, if fault persists Q202 2SC2412K could be leaky | ||
| Sony | FE-1 | No remote control operation | Check as necessary D203 MTZJ-5.6B on main pcb, D907 MTZJ-9.1A on pcb H1 or the remote control sensor IC900 SBX1981-51, part no. 8-742-014-11 | ||
| Panasonic | TX28DK2 EURO 4 | No surround sound | As Mark said in a fault on the Euro 4 , Replace the TDA2030. | ||
| Sony | FE-1 | No remote control operation | Check as necessary D203 MTZJ-5.6B on main pcb, D907 MTZJ-9.1A on pcb H1 or the remote control sensor IC900 SBX1981-51, part no. 8-742-014-11 | ||
| Ferguson | ICC17 | Dead Set | Check DP21, 39V Zener, in the startup circuit | ||
| Lg | CF-28A50T PC-58A | Flyback lines on pic | Check resistor R351 in front of TDA8350Q. It should be 3.6 K. I replaced with 3.8 K and it worked fine. Additionaly check: R708, FR704, FR359, Q351, Q345. If fault persists try replacing the TDA8350Q | ||
| Panasonic | TX-14/21GV1 | No operation, standby led blinking | Replaced C840 47uF, 25v which had gone low in value | ||
| Philips | 28PW6332/05 | Loud bang internally, then completely dead. Plug fuse ok. Set about 4 years old | Internal 4A fuse blown. Bang was 330pF cap 2540 across PSU MOSFET exploding, suspect went s/c. Diodes 6513 & 6511 cracked and s/c. Replaced C2540. Could not get diode 1N5062/BYW55 rep, so replaced all 4 diodes with BY399. PSU MOSFET removed and checked,ok. Voila | ||
| Vestel | 11AK19 | Screen blanked out,with 4 coloured lines two thirds of the way down from the top of pic. Sound OK | R704 100 ohm resistor connected to pin 6 of the frame output chip was o/c | ||
| Goodmans | 285NS | Buzz on sound when volume at low level | Dry joints on earth pegs of heatsinks of audio and frame output ICs - confirmed by comet service, long time ago! | ||
| Bush | 28ZKF | TV seems to be dead apart from the front leds | On main board check Ntype TX BD441 which is clipped to the main heat sink. The clip can come loose causing the TX to overheat and melt its connections to the CB. Remove TX test and if OK solder back on making sure TX has good connection to the heatsink | ||
| Toshiba | 28WD98B | Stuck in standby, 16 volt line low at approx 8 volts | Replaced C872 220uF, 50v, original had gone low in value | ||
| Toshiba | 2573 | Stuck in standby. | Replaced ZP82 o/c And tuner internal short | ||
| Akura | AP2821-S | Dead | Replace RP05 1 meg, 1/4 watt | ||
| Grundig | T55-640 CUC 6300 | Sleep timer box on screen, remote & front buttons not working | Changed the EEPROM IC847 24C04 | ||
| Philips | 25PT4103 L6.2 | Blank screen no audio. No results from tuner or SCART socket. When G2 on LOPT is wound up a red line is visible | Check R3438 3R3. In my case this was o/c and a replacement restored normal opperation | ||
| Sony | KVJ29MN21 | Unable to switch on with remote and no LED display at the front of set | Due to STBY 5v missing. Checked and found the 5v reg/reset IC002. L78LR05D was s/c, replace the IC to clear the fault | ||
| Thomson | 24WK25US ICC17 | No/Low contrast after EHT flashover | Check/replace TL02 and TL59 in the beam limiter circuit | ||
| Jvc | C14E1EK | Tuning drift,worse at high channel no's | Dry joints inside tuner unit, connections between edge of pcb and lugs | ||
| Ferguson | 59K7 ICC5 | Severe vertical jitter on picture, horizontal sides of picture ragged | Replacing the TDA4950 cured the fault |