sanyo Repair Tips
Search: sanyo
Results 351
Results 351
| Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
|---|---|---|---|---|---|
| Sanyo | ED-1 | off with faint st/by led | Q304 2SC536 error amp in psu u/s also check 5v reg | ||
| Sanyo | ED-1 | No pic sound ok | VCU2136 IC501 on digital board | ||
| Sanyo | ED1 | Trips 4 times then dead | R314 10R in psu - LT supply once set has fired up | ||
| Sanyo | ED1 | Pic blanked out at sw on except for 2" strip at bottom | Dry joints Q453 in st/by sw cct | ||
| Sanyo | ED1 | No pic - just bright glow at top of screen | DPU2553 IC508 on digital pcb pt no 409 211 87 01 | ||
| Sanyo | ED1 | Mosaic - like pic | IC502 PVPU2204 (PAL vid proc unit) | ||
| Sanyo | ED0 chassis | No sound | IC1680 TDA7253 & ICP853 o/c | ||
| Sanyo | ED0 chassis | Bright raster - sound ok | R534 22R safety res & check IC500 TEA5101A RGB o/p chip | ||
| Sanyo | ED0 CBP2876A | Dead - LOPTr Q650 2SD1556 s/c | C605 2µ2 line dr coupler leaky was cause | ||
| Sanyo | ED0 CBP2576/2876 | no pic, no sound when entering tuning mode (just snow) | enter service mode and enter correct configuration code 02014 | ||
| Sanyo | ED0 / EB1 | To enter service mode | Press & release diamond memory key on front ("Factory" shows on screen), press Index/Menu on hset within 5 secs; 1st tab on serv menu highlighted to allow entry of config code (02014) from handset. Pressing the R/C menu key again changes OSD to next setting, then alter with "Vol+" & "Vol-". To alter next parameter press sound button (under Vol+ button) to highlight next tab. Recommended values:- HO=02140; SO=01012; S1=00081; AO=00186; YO=00050; PO=15861; ZO=01369; P1=01665; Z1=00087; SP=00009 | ||
| Sanyo | ED0 | To enter service mode | Press/release "Mem" on front panel & "Menu" on R/C within 5 secs | ||
| Sanyo | ED0 | service mode | to enter service mode press MEMORY on TV and withing 5 sec press MENU on remote control | ||
| Sanyo | ED0 | No pic due to field collapse | TDA8170 field chip blasted, R715 N25 cp o/c due to C703 100µ 50v | ||
| Sanyo | EC3A25 CB5956 | Dead with LED flashing dimly | HT at 57v, dry joint on black wire to side of chopper Trfmr | ||
| Sanyo | EC3 CB5156 | when switched on from stby, the set immediately reverts back to stby | in protection mode (pin 31 IC701 below 5V) due to R327 390k o/c | ||
| Sanyo | EC3 CB5156 | drifts off tune | replace C105 1uF 50V near tuner | ||
| Sanyo | EC3 CB5153 | dead | Q432 2SD1651 s/c | ||
| Sanyo | EC2 CB1443 | colours wrong or in wrong order (red is yellow,green is red, blue is green) | IC270 TDA4662 | ||
| Sanyo | EC1-B | Shut down aft 3 secs | Plug for R/C sensor had not been fitted |