sanyo Repair Tips
Search: sanyo
Results 351
Results 351
| Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
|---|---|---|---|---|---|
| Sanyo | CBP2872 ED1 | No sound when sw on if still warm | IC560 ADC2301E on sigs panel pt no 409 211 9404 | ||
| Sanyo | CBP2872 ED1 | No sound - comes on briefly when cold sometimes with crackle/hiss | OK from scart socket - IC561 APU2471 could be faulty | ||
| Sanyo | CBP2872 ED1 | Lines when cold with shading as warms up | C404 (100mfd 50v) in the frame stage was the culprit, although its ESR reading was OK, and there were no signs of leakage | ||
| Sanyo | CBP2872 | REPEAT FAIL OF LOP TR ( 2SD1555 ) | IC DPU2553 | ||
| Sanyo | CBP2872 | No sound from spkrs - ok from scart | IC561 APU2471 on sigs panel | ||
| Sanyo | CBP2866 | Int trip/blank raster/no field sync | IC780 12v reg - use TIP41 & 13v zener & 27v dropper as reg nla | ||
| Sanyo | CBP2865 E3A28 | Picture and sound goes off int. | 12v Reg IC780 failed when hot. | ||
| Sanyo | CBP2865 E3 | Int sound/pic with bright white raster with low height or field collapse reverting to st/by | IC780 SI3122V 12v reg s/c internally when heated | ||
| Sanyo | CBP2865 | INT BRIGHT RASTER WITH REDUCED HEIGHT | REPLACE IC780 12V REGULATOR | ||
| Sanyo | CBP2580A EB2 series | Tripping - even with psu on dummy load | black jumper wire which runs from the earth side of the chopper transformer to a point very close to IC351 a regulator IC, was dry jointed at the chopper transformer end. | ||
| Sanyo | CBP2580 EB125 | This set would shut down interrnittently: the peri | The set could be made to run indefinitely by entering the service mode ( menu on the set's control panel , followed by menu on | ||
| Sanyo | CBP2580 EB1 | To enter service mode | Menu on set's control panel, followed by menu on R/C handset | ||
| Sanyo | CBP2580 EB1 | Shuts down int - runs ok in service mode if IM bus run is stopped | Fault somewhere on the IM bus - NVM3060 EEPROM on digiboard cured fault | ||
| Sanyo | CBP2580 EB1 | Colour lost & pic shifted to right when heated | Xtal X403 pt no 610 217 1037 | ||
| Sanyo | CBP2580 EB1 | AFTER 2-3 Hrs COLOUR GOES AND PICTURE SHIFTS TO R | XTAL X403 DRIFTING Pt No 610 217 1037 | ||
| Sanyo | CBP2580 | St/by only - trips at start up | 22mfd 250v B+ decoupler s/c | ||
| Sanyo | CBP2580 | Int start up - EHT can be heard | Check for int mains switch | ||
| Sanyo | CBP2576A/00 | Bright blue raster with fb lines | IC500 which is a TEA5101A on the crt base pcb. R534 22 ohm was ok. | ||
| Sanyo | CBP2576A ED0 chassis | No raster | TEA5101A RGB chip | ||
| Sanyo | CBP2576A ED0 chassis | Height twitches, int bright raster with fb lines | Resolder conns on digital panel |