sharp Repair Tips
Search: sharp
Results 804
Results 804
Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
---|---|---|---|---|---|
Sharp | DV5932 | FAILURE OF C619 | MOVE R632 FROM THE CLOSE AREA OF C619 AND REPLACE CAPACITOR | ||
Sharp | DV5932 | Dead | D709 s/c Replace with ( BYW56 ) r706 o/c fusible | ||
Sharp | DV5903H D3000 | Soot & whitewash effect & no sync/txt | IC1404 VCU2136A vid I/p ok at pin 39 but dig o/p pins 5, 6, 7, 8 & 9 not all active - chip faulty | ||
Sharp | DV5903H D3000 | Blank white raster | IC1404 VCU2136A AD/DA converter - chip suspect | ||
Sharp | DV5405 | Line pulling & lack of col or no col | OK through scart - caps in SIF module | ||
Sharp | DV5165H | Int blows chopper & LOPTr | C751 100µ 200v - int arcing? | ||
Sharp | DV5165H | Dead - lop tx faulty - when replaced screams | IC751 7805 5v reg chip faulty ( only gives out 4v) | ||
Sharp | DV5161H 4BSA | Field foldover, bright raster then collapse of pic & shut down when warm | Line drive started to break up (IC801 pin 12); 26v supply low at 19v - D501 DX0511BM faulty | ||
Sharp | DV5161H | WORKS FOR 1min THEN SHUTS OFF. ALL SECONDARY SUPPL | C711 1n 2kv | ||
Sharp | DV5161H | White raster with fb lines & trips | R612 22R fusible o/c | ||
Sharp | DV5161H | St/by only | No 12v supply; D602 1N4936 o/c | ||
Sharp | DV5161H | No sound/pic - screen lit with lines with half screen darker | FOP chip - gets hot! | ||
Sharp | DV5161H | HEIGHT VARIES WITH PIC CONTENT FIT MODS , ADD 270K | ADD 110K 1/8W BETWEEN CATHODE OF D801 AND GROUND , - CHANGE C832 TO 100nf , CHANGE NVM TO NEW SOFTWARE VERSION ( Sharp CH-IX1 | ||
Sharp | DV5161H | Electronic Screwdriver | Wire link pins 3 & 6 of plug TB on txt panel. Press "mode" on hset. "Serv" appears on screen. Remove link & use up/down buttons to view menu settings. Press "Mode" button again to exit settings | ||
Sharp | DV5161H | Dead green LED lights briefly flashing red | Dry joints C610 near LOPTx | ||
Sharp | DV5161H | Dead - loptr s/c - R604 flaming | R649 15R 1W across Q1010 coll/emitter hi res & replace R604 3k3 1/3w safety res | ||
Sharp | DV5161H | Blows lop tr aft few mins | Tuning caps C607, 608, 609 & 610 | ||
Sharp | DV5151H | LOSES COL AFTER CHAN CHANGE , SLOW TO LOCK | ADD 8.2 MEG BETWEEN PINS 25 AND 39 OF IC801 Sharp VRD-RA2BE825J | ||
Sharp | DV5150H | Reverts to st/by aft 2 secs | No 24v supply to FOP chip as R612 3R3 safety res o/c - Sharp mod - fit 2R2 safety res & link J13 replaced by 1R2 ½w res | ||
Sharp | DV5150H | Int goes off with crackle | Dry joints C603 6n8 1.5kv |