14GX TV Repair: Common Faults and Solutions.
Search: 14GX
Results: 22
Results: 22
14GX Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 14GX | Flyback AT2079-B4 Substitute | Substitute AT2079-B5 | Marcones de Araripina-PE | |
| PHILIPS | 14GX1618 / 78 | Doesn't start | Transistor 7440 horizontal driver, with cold soldering | MARCONES DE ARARIPINA-PE | |
| PHILIPS | 14GX1515 | Doesn't start | Power supply plate capacitor 4.7x25v 47x25v | Capacitor | ELETRONICA MAURI JUNIOR |
| PHILIPS | 14GX1618/78R | The screen is completely white, full of lines, it's as if the screen were fully open. | R 3469 | Perse | |
| PHILIPS | 14GX1618 | Doesn't tune in to all off-air channels | R3650 15k | Replacelo | ANTONIO NOBREGA [PATOS.PB] |
| PHILIPS | 14GX1619 | Inoperative power supply does not arm | Crimping the horizontal output and with very high tension on the altered fly back pacifier | Replace o fly back | eletroclaudio aguas belas pe |
| PHILIPS | 14GX1619 | White screen with colored retrace lines on the front side and no video | Defective vertical outlet | Replace the same | eletroclaudio aguas belas pe |
| PHILIPS | 14GX1618/78R ANUBIS VA | Jagged image | Cap 6531 47/ 160 volts, one of the terminals was corroded, as it is glued, you can't see it, you can only remove it from the board. | jorge mota | |
| PHILIPS | 14GX1618/78R ANUBIS - VA | TV doesn't turn on | Led on, only on standby, hcc voltage at 1.95v | Transistor 7423 is good, but when I replaced it, the TV turned on again | odivaldo araujo |
| PHILIPS | 14GX1610 | Stop without +b | Replace do flay back at 2079/b4 | bt | |
| PHILIPS | 14GX8510 /54R | Doesn't start | Open resistor r3561 | ||
| PHILIPS | 14GX1618/78R | The screen is completely white, full of lines, it's as if the screen were fully open. | R 3469 | Perse | |
| PHILIPS | 14GX1618 | Doesn't tune in to all off-air channels | R3650 15k | Replacelo | ANTONIO NOBREGA [PATOS.PB] |
| PHILIPS | 14GX1619 | Inoperative power supply does not arm | Crimping the horizontal output and with very high tension on the altered fly back pacifier | Replace o fly back | eletroclaudio aguas belas pe |
| PHILIPS | 14GX1619 | White screen with colored retrace lines on the front side and no video | Defective vertical outlet | Replace the same | eletroclaudio aguas belas pe |
| PHILIPS | 14GX1618/78R ANUBIS VA | Jagged image | Cap 6531 47/ 160 volts, one of the terminals was corroded, as it is glued, you can't see it, you can only remove it from the board. | jorge mota | |
| PHILIPS | 14GX1618/78R ANUBIS - VA | TV doesn't turn on | Led on, only on standby, hcc voltage at 1.95v | Transistor 7423 is good, but when I replaced it, the TV turned on again | odivaldo araujo |
| PHILIPS | 14GX1610 | Stop without +b | Replace do flay back at 2079/b4 | bt | |
| PHILIPS | 14GX8510 /54R | Doesn't start | Open resistor r3561 | ||
| PHILIPS | 14GX 1618/78R | The defect is an all-white screen, full of lines, it's as if the screen is completely open. | Causes open resistor r-3469. check the 180v voltage going to the kinescope board |