M203 Repair Tips
Search: M203
Results 19
Results 19
Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
---|---|---|---|---|---|
Teac | CTM203 PC04A | No Power | Check / Replace power switch, it read zero ohms at contacts - however carbon build-up stops p.s.u. from starting | ||
Sony | GDM2036S | SHUTDOWN DUE TO Q204/H. OUT FAILURE ON D3 PCB | The monitor shut down due to Horiz. scan failure. The H.Out: Q204 and B+/H. Size Reg.: Q217 failed. B+ Filter C405 had lowcapacitance. | ||
Sony | GDM2038 | INTERMITTENT LOSS OF SYNC | Intermittent vertical sync and hor sync when first turned on.Symptom only showed up on VGA graphics mode. Found IC101 to betemperature sensitive using freeze spray and pyco pen. | ||
Sony | GDM2038 | SHUT DOWN DUE TO Q401 COLD SOLDER | Unit comes on with bright raster and shut down. | ||
Sony | GDM2038 | UNUSUAL PIN TYPE OF DISTORTED PICTURE | Horizontal pin type of indentation on both left and rightsides of screen at about vertical center. Not your typical pin type ofdistortion. Only the center 1/3 of the screen was affected. | ||
Sony | GDM2038 | PICTURE IS UNSTABLE WHEN CHANGING FROM TEXT TO GRAPHICS MODE | |||
Sony | GDM2036S | PICTURE IS UNSTABLE WHEN CHANGING FROM TEXT TO GRAPHICS MODE | |||
Sony | GDM2036S | NO HIGH VOLTAGE, AND NO HSYNC DUE TO IC101 (H OSC) | All Power Supply Voltages are OK but, No Horizontal drivesignal from IC101. | ||
Sony | GDM2038 | RECOMMENDED SCREEN CLEANER | |||
Sony | GDM2036S | RECOMMENDED SCREEN CLEANER | |||
Sony | GDM2038 | DIFFICULTY ADJUSTING THE WHITE BALANCE | |||
Sony | GDM2036S | RECOMMENDED SCREEN CLEANER/USE (3-731-449-01) DRY SOFT CLOTH | This monitor has an anti-glare coating on the CRT. What typeof cleaner is recommended? -HQ COMMENTS: All GDM Monitors unlike CPD Monitors have a coating on thescreen surface. We recommend a dry soft cloth (P/N:3-731-449-01) to cleanthe screen surface. | ||
Sony | GDM2038 | RECOMMENDED SCREEN CLEANER/USE (3-731-449-01) DRY SOFT CLOTH | This monitor has an anti-glare coating on the CRT. What typeof cleaner is recommended? -HQ COMMENTS: All GDM Monitors unlike CPD Monitors have a coating on thescreen surface. We recommend a dry soft cloth (P/N:3-731-449-01) to cleanthe screen surface. | ||
Sony | GDM2036S | PICTURE STRETCHES VERTICALLY DUE TO IC-201 | After warm up, the picture will start to stretch vertically atthe bottom. Customers says it would take anywhere from 1/2 to 2 hours.By heating and cooling IC-201 I was able to produce the problem. | ||
Sony | GDM2036S | NO OPERATION, SCREACHING SOUND FROM THE POWER SUPPLY. | |||
Sony | GDM2036S | NO VERTICAL DEFLECTION | Unit has no vertical deflection. Checked and found openvertical Yoke. Tried to locate the open, and found C01 on the Yoke ass'yopen. The coil is made up of large wire, so it cannot be defective. | ||
Sony | PVM2030 | PART NUMBER FOR THE CHASSIS BRACKETS | The part number for the Chassis Bracket is not shown in theservice manual. -HQ COMMENTS: The part number for the chassis bracket is 4-382-023-01.Also see Service Bulletin No. C/P0013. | ||
Sony | PVM2030 | SCREEN NOT COMPLETELY BLANKED | With brightness and picture control turned down and in a darkroom, there is a visible illumination on a part of the tube. This is withno connections to video in. Connecting a generator to the video in andstarting with minimum signal, you can see the pr | ||
Sony | M203 | DEFECTIVE C122 | Newly made recording had low playback volume. LED indicatedexcellent sensitivity during recording but playback was low. Previouslyrecorded tapes were OK. |