PH32F33DG TV Repair: Common Faults and Solutions.
Search: PH32F33DG
Results: 15
Results: 15
PH32F33DG Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PH32F33DG | Does not work.led stby off. | Tsound is no 3.3v power supply | See, replace D406 3.3v power supply protection. (Diode shorted) | Arock |
| PHILCO | PH32F33DG VER. B | No image, backlight on. | Short in the vcon power supply. | Q202 on the main board charred, q1 (dmp3098l) and smd capacitor next to the amp. op p11e shorted on vcon (dmp3098l) | Gabsens |
| PHILCO | PH32F33DG | No image | With the oscilloscope, notice the back light gives a pulse and disarms, change the changed LED and remove 033 resistors | Warley cesar | |
| PHILCO | PH32F33DG | The TV worked normally, after about twenty minutes the sound began to sizzle like AM radio waves. | 220mf/35v capacitor next to the audio IC, which had a low capacitance. | Replace the same. and run to the next repair. I hope I helped my friends. | Bruno Cardoso |
| PHILCO | PH32F33DG | Only flashes standby | Software on the pendrive! found sound on the website! software on the philco website, format the pendrive, insert the 2 files on the pendrive, unplug the TV, insert the pendrive into the TV's USB, turn on the TV with the power button pressed until the software installation menu appears, the TV will reboot and that's it. | Rogério Eletrônicoos | |
| PHILCO | PH32F33DG | Turn on the backlight and turn it off, tsound is only audio | Probably some led changes resistance because I removed the led bars and tested with a power supply they all lit up then I measured the voltage in the white wire led connector and compared it and it was the same as one was less | Put a 1r resistor from another arm wire that goes to the LED bar to the other arm on the side so the voltage will stay the same and the screen will stay on | beto2828 |
| PHILCO | PH32F33DG | Take away characters in the bottom left corner. It keeps showing: mv v8-0ms32la-lf1v017 sv v8-0ms32la-lf2v003 id 64 adc ng p network ok | After an update it looked like this. | Using the remote control: press menu>image>go down to contrast>type 9735>factory hockey and turn it to "off">remove the power cable and it's ready. | Eletrônica R-Tec |
| PHILCO | PH32F33DG- VB | Does not tune the channels. | Electrical surge. | Resistor r103 (1r0) open. | RNSPTEC |
| PHILCO | PH32F33DG | Turns on and then turns off | Voltages ok boards ok, defect in an LED or one of the buses | I disconnected the red LED wire from the board connector and the TV turned on normally, strange but it worked | |
| PHILCO | PH32F33DG | Turns it on, philco appears and turns it off | Tested power supply was ok, all voltages, leds ok, no visible damage to the boards | Side buttons corroded with rust along with the button plate. just replace the board or rebuild it with new buttons | |
| PHILCO | PH32F33DG | Standby LED flashes continuously and does not turn on | Software defect on the main board and flash memory | Download software from the philco website, format pendrive, insert the 2 files on the pendrive, unplug the TV, insert the pendrive into the TV's USB, turn on the TV with the power button pressed until the software installation menu appears, the TV will reboot, then that's it. run to the hug | OSVALDO SEABRA |
| PHILCO | PH32F33DG | Shutdown after about 3 to 4 minutes... | Faulty LEDs. | Check the voltage consumed by each LED bar and replace damaged LEDs. | |
| PHILCO | PH32F33DG | Piscando led standby | Update software | Downloading the update from the Philips website means updating. | Naldo Lima |
| PHILCO | PH32F33DG | Turning off over time if you put a fan behind the TV it takes a little longer | D 201 and q 201 on the main board (this model uses the triangle-shaped board) | With the hot welder I heated the d 201 and in ten seconds the TV presented the defect and on the q 201 I also replaced the d 201 with a bd137 and the q 201 with a bd 140. I don't know if it's correct but it worked on the d201 and it printed code a7w31 and the q201 is printed 2nd 4 good luck everyone I practically stumbled upon this defect | alanrca2 |
| PHILCO | PH32F33DG | Turns on, the logo appears and then turns off | A common defect in this model is one or more broken LEDs. | Before dismantling the panel, check the voltage in the three pairs of wire that go to the LED panel, it must be the same, if tsound is a difference, it is certain that tsound are shorted LEDs in the panel, which will trigger the protection and the TV will turn off. | Miratec Eletrônica |