Cineral TV Repair: Common Faults and Solutions.

Search: Cineral
Results: 427

Cineral Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem	Solution	By
CINERAL	21PCIN0405	No image on av	I short circuited pins 13 and 14 of the 4053 switch		Marcelo
CINERAL	14N CIN	Image shifted to the right, black band on the left and no characters	Position smd diode d408	Replace d408	Fofao estância
CINERAL	14N CIN-0401	Does not turn on or stand-by when the weather is cold. By exposing the TV to some heat power supply (e.g. getting hot in the sun) it turns on normally.	Defective primary power supply electrolytics or low capacitance.	Replace with new or in good condition. preferably, replace all the primary electrolytics (including the 150 μF "biteludo" for 400v). If you need a schematic, use the Philco ph14 "game" one.	Tiago C. Neves
CINERAL	CIN-401	Disappear image, lit filament and normal sound.	Poor abl tension. leaving the screen very dark the image remains, increasing screen some image	C415 470μF x 25 v	Pardal-x
CINERAL	TC-1433N PTFM05-1	Dead TV wouldn't even turn on standby.	When removing the q 404 (horizontal output) the TV oscillated, damaged the degausser relay and lit up the LED, and the cause of the q404 burning was the shorted flyback.	After exchanging the two, I just ran for a hug.	Marcio eletronica
CINERAL	TC1466	TV turns on and off immediately	Only replace cap.318/4.7/50	I	Adão S L
CINERAL	R-FLAT 2166	Does not turn on LED blinks without power supply +b oscillating 10 to 14v	Q804 = c1815 defective	Replace for a new one	EletronicaAlmiro
CINERAL	29P CIN 0507	Pink image. no green.	R 520 (2k7)		NEW PEK ELETRÔNICA
CINERAL	29P CIN-0507	Unlock without control	Improper programming		Leonardo
CINERAL	29P CIN-0507	Has sound but no image	Open resistor 6.8k position on board r432	Replace with new	<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
CINERAL	TC-2033N	Ticking ticking and low secondary power supply	Solved 130k resistor r 834 open	Replace r834	beto2828
CINERAL	TC-1470	Vertical closed	Q102	Replace q102, put bc337	Marcelo Piranga
CINERAL	21P CIN-0405	It turns on normally but with a black bar on the left side of the screen.	Q409	Replace the c409 in the fly-back foot	Sinailson furtado
CINERAL	29P CIN-0507	Inoperative, does not turn on, LED is off	Ic 801 with faults	Just replace it and the TV is 100%	Nilson Rodrigues
CINERAL	TS 2944	Connects white screen with lines	Resistor on the 210 volt line for the tube plate	I replaced the resistor and a diode close to the tda 6108 on the tube board and the tda was also bad, I replaced it, solved	Samuel silva
CINERAL	21PCIN 0305	Closed and inverted screen	Tip arock hit..	Replaced the 301 for another... I didn't have a 4001 and replaced it with the 4004	Mauro
CINERAL	21P CIN-0405	Doesn't start	Photo coupler	Replace	davi.sls
CINERAL	CIN0305 .	Does not turn on LED. and when it turns on, it only turns on via the control and with the vertical closed at the bottom.	The reason why it only turns on via the control is the keys on the keyboard. and the cause hanging with closed vertical is the eepromm memory. note; also change the 100/35 volt c302 which was exhausted.	Replace the keyboard keys and the c302 with 100/35 vertical turns.	<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
CINERAL	TC 1470	Vertical risk (without horizontal deflection)	Open capacitor c214	Replace and run....	Matrix
CINERAL	R-FRAT 2166 40-ONX 56BMAF-1XG	TV didn't light up OLED but had +b 105v normal but didn't have 3.v	Capacitor c872 of 100mf at 16v, a 100mf at 25v was placed and the TV looked great	Don't thank me but thank the electronics	<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>