Samsung TV Repair: Common Faults and Solutions.
Search: Samsung
Results: 3802
Results: 3802
Samsung Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | UN55TU8000 | Turns the backlight on and off | internal short in the screen | In the first COF on the left, cut the lines CLK1 to CLK8. | Persio (TVCompany) |
| SAMSUNG | PL51D490 | Grainy/almost 100% dark picture after replace RPJ30H1 or FGPF4536 IGBTs | Y-sus burning R5126 (6R2), shorting out several ceramic capacitors on the line. | The short is actually in IC U5014. After replace it and replace the 6R2 resistor once again, it started working again. | World TV - Sorocaba |
| SAMSUNG | UN49NU7100G | Half of the screen was bright, the other half was dark. | Broken jumper on the power supply board | A Jumper at the mosfat output that controls one side of the LEDs has a jumper under the heat sink of the 2 diodes and 2 fats on the secondary, just reconnect the jumper and it works again, but even so you have to reduce the current of the LEDs on this model . | Eletrônica ATM |
| SAMSUNG | UN40FH5303 | turning off the back light, or turning it on and not turning on the back light | on the main board defective blu line | q204 smd transistor any npn will do, I put bc817 | Ariel Santos |
| SAMSUNG | 46ES6100AGXZD | Stand by LED does not turn on | trafo tsth01 | on the primary part of the transformer, one of the terminals opens in relation to the chassis, see that it has a darker and more oxidized pin, just redo the soldering or put a jump to the pci | paulo pinho |
| SAMSUNG | UN43AU7700 | Completely stopped, not even standby | Screen drive board with shorted capacitor c203, however when trying to turn it on, the board was also inoperative, when checking it was found that two 13v fuses that came from the power supply were burnt, after replace them the TV started working again with shorted ceramic capacitor c203 | Replacement of c203 on the screen drive board and replace of fuses at the main 13v input, coming from the power supply. | Cosme |
| SAMSUNG | UN39FH5003G | TV turns on, backlight turns on and then turns off, won't turn on again. unplugging it after a while repeats the defect. | QM805 on power supply board - SMD NPN Transistor | Pardal-x | |
| SAMSUNG | LT24/27C310LB | The LEDs don't light up | TV arrived with sound and no picture, I immediately imagined it was the LEDs! I opened the display and the LEDs were 100%! Tsound was no voltage to power the LEDs! Voltage arrived at the SLC5013R ci (ic1701_ad) responsible for the voltage of the LEDs. | Replacing the SLC5013R ci | Rafael Sena |
| SAMSUNG | UN40EH6030G | It doesn't turn on, and when it does, it turns off right away. | Transistor do POWER ON. | To test if the regulators are good, just release the Power On wire from the harness and see if the regulators on the board are working, if everything is working, without the power on connected the TV has to turn on, if it turns on and works perfectly, You have to analyze if it is not the Power On command transistor, tsound is one on the power supply and tsound is one on the main one, in my case, it was the bad main one, it is in position Q203, between the HDMI and the Optical Audio, just replace it and receive the Pix. | Eletrônica ATM |
| SAMSUNG | LN32C530 | Does not turn on - st-by off | Voltage enters regulator IC205 and tsound is no v-out, capacitor c268 is shorted. | replace.. | Maurilio |
| SAMSUNG | UN32F4200 bn44-00604a | replace LEDs reducing LED current | bad ledsa remove the 3.6r 2w r9110 and replace it with an 8.2r 3w one | replacing the resistor to reduce the LED current and increase the last life | orlando lott |
| SAMSUNG | UN46F5200 | CURRENT REDUCTION LEDS | remove smd resistors r9109 and r9210 | reginaldo moronte,eletronica junior caldas novas | |
| SAMSUNG | UN40H4200AG | Does not turn on, standby LED flashes 6x backlight off | Q211 3.3v regulator had 2.2v at the output | MACIOTI | |
| SAMSUNG | LN37C530F1M | turning off when programming channels | software problem | Even after updating, the defect persists. You can try going to the option function (service mode) in DDR leaving it at two and in Sub optiom in the support function lna leaving it at 0 | Marcos Paulo Infotron-ltda |
| SAMSUNG | PN43H4000 | picture, blurred, negative, drizzle vs normal voltages, va and vsc | Q 5010 (sun 0550) with leakage plate and its | replace | Hndrsn |
| SAMSUNG | UN50MU6100G | TV turns on backlight but no picture comes out, tsound is audio. | Medir Q210, enter 12.5v and you know 12.5v. | replace Q210 (4435) was inputting 12.7v but outputting 11.5v. The Q210 got very hot. It looked like an LCD defect. | Joaomvjr |
| SAMSUNG | UN50TU7020 CY-BT050HGPV1G | doesn't start | MAIN BOARD DOES NOT TURN ON SUPPLY OK | JOÃO GAIA | |
| SAMSUNG | LN32R71B GBD32ML | With picture on HDMI and sound showing hissing noise | I checked for a short in the STV8257 audio processor, found the capacitor C6015 (SMD 10uF/16V) with low insulation measuring 32 ohms, replaced it and the audio returned to normal. | Erick Geraldeli | |
| SAMSUNG | 29K40MQ | does not oscillate horizontally | r425 1k resistor replacement | reginaldo moronte,eletronica junior caldas novas | |
| SAMSUNG | UN40D5003 BN44-00473A | Standby LED blinks and does not turn on | Releasing the cable that powers the main one activates the backlight and the power supplys, but it is the power supply board. | Leaky QQ9101 transistor, backlight shield near the backlight connector. | Easi |