Repair Tips
Search:
Results 37055
Results 37055
Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
---|---|---|---|---|---|
Hitachi | C2558TN G8Q | This set would not switch automatically into A/V mode when a video or any other equipment was connected via the scart | The set could manually be placed into A/V from the tv's front end controls. The cure was to replace ZD301 ZTE251. I assumed it was a 2V but as i had none in stock i tried a 2.7V zener which worked perfectly. It's located near the scart socket | ||
Proline | 28N1 F19 | Int will lose eprom settings, ie Height etc | The Crt base was arcing internally | ||
Bush | 11AK19 | Lack of width / no ew control | The east west fet Q603 BUK444-200A was short and R629 2.7ohms fusible was open, replacing both cured the problem. 2 Values for this component: 2.7 ohm in 90 degree crt's ... 27ohm in 100 degree crt's. 32" models value is 56 ohm @ 1 watt safety | ||
Grundig | CUC3500 | No sound AV-Mode sound ok | Replace IC2210 U2829 | ||
Bush | 34BKB 3463NTX/4400 | Dead / excessive width and e/w bowing | Capacitor CL15 was dry jointed and transistor TL4 was s/c, also CL18 22uF, 250v was stressed, after replacing these components had excessive width and e/w bowing, the TDA8350Q field ic turned out to be the culprit | ||
Sony | KV20TR22 | Intermittent reception on VHF / UHF | Resolder tuner especially the around the tuner I.C | ||
Sharp | TV14 Cinema Borg | When set switched on "ENTER YOU LOCKCODE" appears on screen, customer had forgotten the lock code | Replaced the Microprocessor64 pins | ||
Philips | 14GR1221 GR1AX | Procedure to enter or exit hotel mode child lock | Put the set on programme 38, press either store and pr - to lock and store and vol - to unlock, or, press pr - and vol + to lock and unlock, press buttons on the set not remote | ||
Philips | GR2.2AA | Dead, no line oscilation, power supply and line output stage are OK | Check / replace C2549 390 or 470nF / 400V and C2545 1n5 or 1n2, 2000v | ||
Philips | GR2.2AA | Does not work after LOT has been changed | Check / change D6561 also change the TDA2579B if there are any sync problems | ||
Sharp | 66FW53H | Dead - Neon lit | R713 and R714 560K high or o/c | ||
Sharp | 66FW53H | Dead - neon lit ... another fault! | Check the BZW04145 diode across C720, if short circuit, replace and also replace opto-isolator IC704 MOC8106 and IC706 TL431 voltage reference. You can put an 817 opto-coupler in diagonally | ||
Mitsubishi | BDS29S 11AK19 PRO | Picture is black with faint green retrace lines, sound etc. ok | Changed TDA6108JF on CRT board, and nearby 10uF electrolytic which looked damaged. Fixed fault. A resistor next to the capacitor had been changed before but tested okay this time | ||
Samsung | CX5012 | Volume low, even at maximum setting | Replaced IC601 TC4066BP close to IF can | ||
Philips | GR1AX | Sometimes does not start up from cold, but starts well from power off or standby after a few minutes | After checking all PSU components and consulting many colleagues, casually the tip of my iron touched the body of T2628 BF423 and the set started. After more then 20 attempts, I realised that this transistor became intermittent when cold | ||
Philips | Various | Sound but no picture | Have found on some Philips | s if they are older then 15 years that a 2.7r resistor close to the HT transformer goes open, resulting in sound but no picture | |
Sharp | 66FW53H | Colours ramping, poor greyscale | Replace IC1002/3, Set will need reprogramming afterwards | ||
Jvc | AV25SD4EK | Standby LED changes from Red to Green as normal, but no picture or sound. Set appears not to come out of standby | Check for dry joints on the line output transformer tags. Resolder all as a precaution anyway | ||
Seg | CTV7951GB | Dead set | Check the following caps, C828 1000uF, 16v, C817 1000uF, 16v and C848 100uF, 25v. The caps take out the following components in the power section. Chopper FET Q802 2SK2545 equivalent BUZ901A need to isolate BUZ901A from heatsink, R817 2.2ohm/5W, D805 BA159, D802 IN4007 and D801 IN4007 | ||
Samsung | CS3339Z | No picture No sound | Faulty IC TDA6107q on crt board |