sharp Repair Tips
Search: sharp
Results 804
Results 804
Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
---|---|---|---|---|---|
Sharp | DV5131H DV5150 | NO CHROMA AFTER CHAN. CHANGE OR SLOW TO LOCK AFTER | ADD 8.2M RES. BETWEEN PINS 25 - 39 OF IC801 | ||
Sharp | DV5131H | psu blown | chopper tfmr pri s/c T101 | ||
Sharp | DV5131H | NO TEXT NVM DATA COUPT REPLACE C714 WITH 2200uF | C714 2200mfd Sharp VCEAGA1CW228M ZENER Sharp RH-EX0413BMZZ ( PIN 5 + PIN 6 CATHODE ) | ||
Sharp | DV5131H | NO TEXT , POOR FIELD , NO PICTURE , INT PICTURE . | FIT 2 8.2v ZENERS FROM PINS 8 & 7 IC1002 TO PINS 1 & 2 ( PIN 8 +ve , PIN 1 -ve . PIN 7 +ve , PIN 2 -ve ) , FIT 10nF ACCROSS P | ||
Sharp | DV5131H | Long time to come on | C1006 22µ 50v near field chip | ||
Sharp | DV5131H | Int Txt/loss of chans | IC1002 EEPROM (blank 24C02P unsuitable) | ||
Sharp | DV5131H | FOLDOVER WITH COLOURED FLYBACK LINES | REPLACE C712 100MFD 35V | ||
Sharp | DV5131H | FAILURE OF IC501 DUE TO INCREASED F.BACK | Replace IC & remove jumper from D502 & replace with 4.7V zen as marked also fit D503 as marked PtN DX0501BMZZ | ||
Sharp | DV5131H | Dead | Start up supply to TEA1039 only 2v (15v); R728 3k3 fusible o/c; D707 RGP10G | ||
Sharp | DV5131H | Blown psu | Chopper tfmr T101 has s/c pri windings | ||
Sharp | DV5131 S3B | St/by only ; 5v & 12v supplies not being sw on by Q703 & Q707 | Fusible R744 o/c - replacing it only restored 12v - check D732 & 733, one was nearly o/c | ||
Sharp | DV5131 S3B | Int won't come out of st/by with LED flashing | R745 0R33 risen slightly - To adjust the B+ set R739 for 14 volts on D712 | ||
Sharp | DV51083H D3000 | Faint raster which can't be turned off by R/C or hor bars | C1485 47µ 50v, C1442 10µ 16v on dig vid panel. Also change C732 & C710 in 5v supply & C719 1000µ 6.3v in 5VM supply | ||
Sharp | DV51083H D3000 | Dead. When the collector of the 2SD1546 line outpu | The line output transformer was faulty. Fit a replacement and power the set up slowly via a variac. If at about 100V input th | ||
Sharp | DV51083H D3000 | Dead - HT present | C715 1000mfd 16v in 5VM supply | ||
Sharp | DV51083H | Tripping & various faults | Fault on digital sub panel (uses the ITT Digit 2000 chipset) & is very unreliable - as each chip costs £20+ & entire panel replacement is advised by Sharp (£200) - repair is usually uneconomic | ||
Sharp | DV51083 D3000 | Trips after LOPTx replacement | FOP chip TDA8175 s/c & supply res 1R o/c | ||
Sharp | DV51083 D3000 | Tripping continously - int originally | C715 2200 16v LT res cap low cap | ||
Sharp | DV51083 D3000 | Dead - HT ok when LOP dis'd | LOPTx faulty | ||
Sharp | DV51083 | Weak R when heated | Set up grey scale via hset |