sanyo ED1 Repair Tips
Search: ED1 sanyo
Results 21
Results 21
| Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
|---|---|---|---|---|---|
| Sanyo | ED1 | Unable to change chans via front or r/c | Adjust G2 volts - micro tied up due to low emiss crt | ||
| Sanyo | ED1 CBP2872 | No colour | PVPU2204 chip | ||
| Sanyo | ED1 CBP2572 | Service mode access | 1). Press and release memory key (diamond) on front panel. (Factory shows on screen) 2). Press Index/Menu key on remote control within 5 seconds. The first tab on the serv.. menu was highlighted allowing me to enter the configuration code (I had been told 02014 was required) directly from the keypad. Pressing the remote menu key again changed the on screen display to the next tab heading "Geometry" with a list of features HO, SO, SI, AO, YO, etc............ with the top one HO being highlighted and vertical amplitude and a number written alongside. Sure enough operating either VOL+ or VOL- enabled adjustment of the on screen number and the vertical size of the picture displayed. To alter the next parameter, press the sound button [under the volume + button] to highlight the next tab down. The recommended values are as follows; CONFIGURATION NO. 02014 SETS SOUND INTERCARRIER/STANDARD ETC. HO 02140; SO 01012; S1 00081; AO 00186 YO 00050; PO 15861; ZO 01369; P1 01665 Z1 00087; SP 00009 | ||
| Sanyo | ED1 CBP2572 | Field collapse at top of screen | C460/461 1000µ 25v, C408 4µ7 50v, IC401 TDA8172 & R464 1R 1w | ||
| Sanyo | ED1 | Trips 4 times then dead | R314 10R in psu - LT supply once set has fired up | ||
| Sanyo | ED1 | Pic blanked out at sw on except for 2" strip at bottom | Dry joints Q453 in st/by sw cct | ||
| Sanyo | ED1 | No pic - just bright glow at top of screen | DPU2553 IC508 on digital pcb pt no 409 211 87 01 | ||
| Sanyo | ED1 | Mosaic - like pic | IC502 PVPU2204 (PAL vid proc unit) | ||
| Sanyo | CBP2872 ED1 | No sound when sw on if still warm | IC560 ADC2301E on sigs panel pt no 409 211 9404 | ||
| Sanyo | CBP2872 ED1 | No sound - comes on briefly when cold sometimes with crackle/hiss | OK from scart socket - IC561 APU2471 could be faulty | ||
| Sanyo | CBP2872 ED1 | Lines when cold with shading as warms up | C404 (100mfd 50v) in the frame stage was the culprit, although its ESR reading was OK, and there were no signs of leakage | ||
| Sanyo | CBP2572 ED1 | WHITE DOT PATTERN | DTI2223-06 , ON DIGITAL PCB | ||
| Sanyo | CBP2572 ED1 | To reprog NVM memory chips | Press service button (thro' hole in set front) & VOL+ together - be careful - all previous data will be lost! | ||
| Sanyo | CBP2572 ED1 | STRANGE E/W FAULT | CHECK DPU2553/75 ON DIGI BOARD | ||
| Sanyo | CBP2572 ED1 | Q903 s/c R301 ( 3R9 ) o/c | Check R3165 D/J and TEA2260 | ||
| Sanyo | CBP2572 ED1 | Int loss off air signals | Q173 D/J | ||
| Sanyo | CBP2572 ED1 | EW faulty | DPU2553/75 deflection proc chip | ||
| Sanyo | CBP2572 ED1 | Dead | R301 3R9 15w surge res o/c, Q303 2SC4429 chopper tr s/c, R315 dry joints caused it-also IC301 TEA2260 faulty | ||
| Sanyo | CBP2572 ED1 | Dark & lacking contrast | Unable to get "OK" indication when adj A1 volts in service mode. IC501 VCU2136 on digital pcb faulty - pt no 409 212 0608 | ||
| Sanyo | CBP2572 ED1 | Blank raster, no sound or OSD | 2 x NVM chips on sigs panel sus; can be replaced or reprog |