M200 Repair Tips
Search: M200
Results 23
Results 23
Make | Model Ch. | Symptom | Problem Solution | Solution | By: |
---|---|---|---|---|---|
Hikona | RM2002 | No sound. | Q201 ( BC238 ) but diff legout , TA7680 | ||
Hikona | RM2002 | No sound | IC101 TA7680 Audio o/p chip pin 1 (vol cont) should read 5.8v at min vol & 0v at max. Was not varying - Q201 faulty - BC238 does | ||
Hikona | RM2002 | Crackle on sound unaffected by vol setting | check 47µ tant coupling cap under IF screening can | ||
Fidelity | CTM2000T | Tripping | 10nf lop tuning cap burn up & BU508A lop tr leaky | ||
Fidelity | CTM2000R | Loss of sync when heated | C100 33µ 250v HT res cap (HT still measured ok at 119v) | ||
Sony | TAM2000 | NO FUNCTIONS - REPLACE IC1, P/N 8-759-276-39 | No functions, although power light turns on, unit overheats.Won't go beyond initial test mode. | ||
Sony | TAM2000 | WON'T RECEIVE CALLS/CANNOT PROGRAM ANY FUNCTIONS | Won't receive calls/cannot program any functions. | ||
Sony | TAM2000 | LOUD BUZZ WHEN PLAYING BACK OGM OR MEMO - CLEAN S401. | UNIT WOULD PLAYBACK OGM OR MEMOS WITH LOUD BUZZ ON TOP OFAUDIO BUT ONLY WHEN MESSAGE/MEMO WAS RECORDED WITH S401 IN THE ANNOUNCEONLY POSITION. RECORDINGS MADE WITH S401 IN OTHER 2 POSITIONS WOULDPLAYBACK NORMALLY AS WOULD ANY ICM. | ||
Sony | TAM2000 | ANY PHONE HOOKED UP TO MACHINE IS DEAD - REPLACE Q301 | Unit would not power up and also was shorting line (dialtone), making any phone hooked to unit appear dead. This occurred evenwith TAM2000 unplugged from AC adapter. | ||
Sony | M2000 | TAPE SPEED VARIES | Pinch roller will not contact capstan. Tape speed varies.The shaft that connects with spring 59 is bent or part of the pinch rollerassy is bent. | ||
Sony | ICFM200 | NO SOUND - REPLACE Q8, P/N 8-729-904-87 | Had no VCC on IC1 trace to Q8. | ||
Sony | ICFM200 | NO POWER OR INTERMITTENT POWER - REPLACE IC4, P/N 875993761 | The unit had no power at all. After removing back of unit,the unit would work when the main board was tapped. I followed thevoltage to IC4 and found that IC4 had 5.1v going in and 0v coming out.After replacing IC4, I had 2.7v out, but still no power. | ||
Sony | GVM2000 | RECOMMENDED SCREEN CLEANER/USE (3-731-449-01) DRY SOFT CLOTH | |||
Sony | M2000 | AUTO BACKSPACE DOES NOT WORK | Auto backspace does not engage. A shifting lever in themechanism which shifts gears reference numbers 80, 82 -performs functionsof fast forward and fast rewind. It does not shift smoothly and quicklybut the functions of fast forward and fast rewind do | ||
Sony | CPM200 | AVAILABILITY OF REPLACEMENT PARTS | The flexible pipe assembly and base are not available asreplacement parts in the service manual. | ||
Sony | HVM200 | BLOWN FUSE F-101 | Blown power supply fuse. Apparent confusion over what powersupply is required. No specific Sony supply specified in manual. Note -error on front page of service manual under power consumption. Also,page 5 of service manual, item 13, connect the land | ||
Sony | GVM2000 | SUPPORT BRACKET PART NUMBER (A BOARD) | Support bracket for the A board on the GVM-2000 is needed.No part number is listed for this item in the service manual. -HQ COMMENTS: The part number for this item is 4-393-914-02. Pleaseupdate your service manual. | ||
Sony | HVM200 | DOES NOT OPERATE | The leads on the DC-DC converter board punch through theinsulating sheet and short out on the shield below it. This damagesthe converter. | ||
Sony | GVM2000 | NINE-PIN ADAPTOR | Nine-pin D-type adaptor that comes with the unit is notidentified with a part number in the service manual. | ||
Sony | ASM200PS | REDUCED SENSITIVITY TO SCENE CHANGES | The unit does not set off the alarm when small changes aremade in the monitored scenes. Changes have to be very large to set offthe alarm. |