philips MD2.22E Repair Tips

Search: MD2.22E philips

Results 85

Make	Model Ch.	Symptom	Problem Solution
Philips	MD2.22E 29PT9113	white box with line in it at bottom LHS of the screen	auto subtitle selected, but not being transmitted, turn off with button under flap on R/C
Philips	MD2.22E 29PT9113	no tuning	R3568 56k 0.5W on large signal panel (+40V supply to tuner)
Philips	MD2.22E 29PT9113	bright red raster	R3351 120k o/c
Philips	MD2.22E 29PT9113	at switch on green LED comes on for 10 secs, then switches to stby (red)	Micro M27C801100F1V00640
Philips	MD2.22E	at switch on set goes into protection mode	Replace C2524 with 10uF
Philips	MD2.22E	Wrong TXT characters on subtitles	Replace position 7202 on the TXT & control module by: 4822 900 11102 Software for non EPG sets 4822 900 11066 Software for -/58 sets 4822 900 11058 Software for EPG sets REMARKS : IRIS symptom code 1286
Philips	MD2.22E	Vertical stripes in picture	On the right side a 2.5 cm width dark band and on the left side a vertical stripe can be seen. Check if the wires S11-L11 and S10-L10 do not touch C2368 on the SSP. If they touch C2368 bend them away from C2368.
Philips	MD2.22E	Vertical shift and amplitude not stable (jumps).	Check pins of connector J13 on the DDP. Look for badly soldered (oxidated) pins. Resolder pins if required. REMARKS : Improved connectors introduced in production from week 9742 onwards.
Philips	MD2.22E	Unstable moving, "waving" picture	Check on +5 V panel the soldering of C2530. Also check and resolder pin 1,2,3, and 10,11,12 of connector V50 on the LSP.
Philips	MD2.22E	Two vertical grey bars in picture	Bent flatcables S10/L10 and S15/L15 away from TDA9143 (pos. 7352 on the SSP)
Philips	MD2.22E	Totally inoperative, red LED slowly flashing; +5V is 2,2V	Check/replace diode D6520 (1N5822; 5322 130 32677) on the +5V panel.
Philips	MD2.22E	Totally dead	If the mains fuse (2 amp; 1501 on the mainsfilter panel) is defective, replace it by a 6.3 Ampere hard break (4822 253 30467)
Philips	MD2.22E	The time from TXT is not read or with mistakes	Replace position 7202 on the TXT & control module with: 4822 900 11102 Software for non EPG sets 4822 900 11066 Software for -/58 sets 4822 900 11058 Software for EPG sets REMARKS : IRIS symptom code 1286
Philips	MD2.22E	The colours are switching during playback of mounted video tapes	The colours are switching during playback of mounted video tapes on several camcorders. In case a TDA9143 is present on position 7352 on the SSP: - change position 7352 into a TDA9141 (4822 209 90328) - remove position R3377 and R3378 (20M) from the SSP
Philips	MD2.22E	The bottom left side of picture shows a green teletext symbol	The bottom left side of picture shows a green teletext symbol whether or not the teletext is switched on. Subtitling is selected, but the subtitling page is not stored. Switch off the subtitle function by pressing the subtitle knob on the remote cont
Philips	MD2.22E	Switching off and on of the wireless surround speakers	Check and replace the following components on the power supply + amplifier panel in the active surround speaker if necessary: - position 2280 into 220uF (4822 124 40196) - position 3280 into 330k (4822 116 52272) REMARKS : IRIS symptom code 6544
Philips	MD2.22E	Subpages not stored/updated in menubar	Check whether jumper 4400 is present on TXT-control panel. If not present, mount jumper. The location is between X-tal 1201 and TXT IC7400. Codenumber jumper: 4822 051 20008.
Philips	MD2.22E	Stand-by LED flashing after start up	Errors 47, and possible 69 are indicated. Solution: on LSP probably HFB signal not present caused of defective R3609, 4k7, 4822 052 10472.
Philips	MD2.22E	Sometimes still picture occurs	Check and replace if necessary IC7400/IC7441 (TDA8753AN; 4822 209 90528) on the feature box.
Philips	MD2.22E	Set switches to stand-by	Change software into the V_3104 317 00890 (4822 900 11058) REMARKS : Introduced in production from week 9737 onwards.