Search: LG
Results: 4834

LG Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
LG29K30
MC-022
TV turned on with retraction lines and turned off I found the capacitor on the 220v line swollen in the rear, it's the others on the line didn't solve itTda6107jfTda6107jfELETRÔNICA MUNIZ
LG26LG30R
Turns on, with audio, screen lit brightly and without characters. changes channels but no image.Tcom without power supply.Replace double mosfet si4925bdy behind the tcom jack.BICHARA
LGLG26LG30R
Does not turn on, red LED flashes blue twiceSupply missing 12volts and 24 volts lowReplace transistor stn 2222 (replacement bc 639. invert the cbe and ebc terminals)BICHARA
LGCM4330 EAX64991501
Sometimes it turns on, sometimes it doesn't.6v2 zener diode, position zd902 and 6.8nano polyester capacitor position c908, changed.Swap 6v2 for 8v2/1w and 6.8nano for 10n/50v and that's it...LUCIANO ALQUEJA
LG42LG50D
Doesn't startFet q601 with leak, fb601 open, tv already turned on, but pfc wouldn't bend, ci u601 defective.Replace these parts and the TV was okMaurilio
LG21FU4RL
Power supply low TV does not oscillate secondary 85vR844 of 4k7 measuring 6k2Replace 844 4k7JUNIOR
LGMCT704
So no standby (relogio), sem audioIt only arrived on standby, it was a CD2 touch key, then it turned on normally but tsound was no audioI tried everything to solve the audio problem but without success, tsound was no =65v or -65v for sound output, the only solution was to place a 33k resistor between pins 3 and 4 of the pc901 photocoupler and another on the pc902, the voltages returned +65v and -65v and sound working normally, it was the only way...Gleyton
LG42PJ350
PD01A
It turns on and then goes back to standby and doesn't turn on again until you unplug it.It was verified that q605 did not release 12v for the doubler and the ic l6599. photo 103, responsible for switching this transistor, was changed.joaomvjr
LG29FU6TL
Change channels, adjust the volume, but with the screen completely dark. normal scrim voltage. Acting on the screw potentiometer quickly, a slight glow appears and goes out. with the normal vertical (open).Vertical ci defective ic301 (stv9326 ) and open fr401 0.05 homs.Ademir tc
LGCM-8350
No audioFotoacoplador pc902Replace the sameriva ferrari
LG29 FX5CL-LG
Does not turn on the off LED, it just breaks the relaysIt was the 180k r830 that was openThe TV turns on but turns off immediately afterwards tsound was another resistor open, the r843,220k open, replace bothRafael
LG32PC5RV
Power supply relay knocking, no voltage vs and goes without 5v, it also applies when it works and keeps turning off for no apparent reason okR122 r123 r124 1004 or 1mg remove clean glue replace, check voltage with digital multimeter on each one, tsound should be 90v on each one as it is a dividerLuiz Técnico
LGRP21FE85G
No image only soundC512I replaced and ran to another oneAntonio Carlos (Eletrônica Renascer)
LG42LB5500
TV had sound, had black light, but dark image, main board and power supply, t-com good.Display board with shorted capacitor, c103Turn off one of the flets to find out which side has the problem. whichever side is bad, has half of the screen white. and just replace the 10 midro caspacitorELETRONICA MOISES
LG32LD350-UA
LA04A
Turns off after some time. After the first shutdown, this repeats more quickly and then never stops turning on again. keeps turning on and off.Zd503 diode (zener 15v) leaky/altered. only detectable at x10k scale. Measure to see if possible changes in the zd504 (15v zener, very close to the zd503) and ic 502 photo coupler.Replace and you're done.Eletrônica R-Tec
LG29FX5CL
CW62A
Closing on the sidesResistor r319 of 39k measuring 53k3R
LG42PQ30R
Sometimes the relay doesn't even turn on the LEDD352 shorted diode.
LGRAD 136
No sound comes outTsound is no voltage at the outputZener 905 uz 20sb(20volts), close to the rectifier bridgeeletronica fernandes - to
LG42PJ350
The image is drizzly and dark and only appears a little at the top.R729.2r2 and capacitor c765 1k x2kv and I guided by the words of friends sound.Replacing them. open resistor and cap. blown on the y plate.@gepe (agripino sousa) Pá
LG42PJ350
TV would hit the relay and go into protection. stand by access but did not accept the power on command. and none of the 5v voltages appeared on connector p813Transistors q801, 802 and the driver l6599d fuse f801.Replacing them.@gepe (agripino sousa) Pá