Search: LG
Results: 4834

LG Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
LGRP-21FD15
Inoperative.The LED lights up, when executing the command the LED turns off, the TV does not oscillate and returns to stand by condition.Cold welding mainly on the power supply, regulators and vertical circuit.Elisson Aragão
LGRP20CB62
It doesn't turn on. When we try several times, it turns on but is stuck on one channel, not accepting any commands from the CR or the panel.Change eeprom|(24c04) and program setup parametersELETRONICA ESTSUDIER
LGRP14CB20A
Vertical with height deficiency (I noticed that the sides varied when the image changed)I verified that the power supply +115 the 47/160 capacitor had low capacitanceBy changing the vertical capacitor it was normalizedfernandocamarques
LGCP14K42
It fires when it turns on then turns off (note all voltages are present at the moment it fires)Defective vertical output (la7833) note tsound is no point in removing it from its place, the ap only works with it in place)fernandocamarques
TV LGLG.29FS4RLG
X-shaped screen or non-standard convergenceReplaced or capacitor c 461- 0.047 uf 630 votes capacitor exhaustedjaironuness
LGRP-20CB67
TV just stays on stand by, similar symptom to defective PCMoisture between the micro pinsWhen you have this device, you suspect the computer; before changing the computer, remove it from the board and wash the computer, thoroughly to remove dirt between its pins.Roberto Consertos
LGRP21FE85
When the device is cold, it does not turn onCrystal x1 and cap. c11 and c12 (both with escape)Replace them next. to ic501MAXWELL ELETRONICA
LGCP14B85
--------------------
Contrast function did not workPosition resistor 550 (10k) openReplace resistor position 550 (10k)Clayton
LG710E
MONITOR 17``
Dark imageIn addition to the other one I already wrote, I got another one with the same defect, but this time it was the ci of the kinescope plateReplace the ciAdrianChapadão
LGRP-21FE85G
Turning offRr420=240k,http://rmeletronica.com.br
LGCP 14B86
Contrast does not work, without contrast502 diode shorted or leakingwillamis
LGRP-29FA30A
MC022A
No plot and no soundTv lg flatron rp-29fa30a was without plot and without sound. when pressing the power button it produced an intermittent hiss...like tshhh.....tshhh.....in the tsh collector tsound was also an intermittent +b, varying between 110v and around 70v. It was possible to observe that tsound were some voltages originating in the fly-back secondary, quite reduced and also varying, but tsound was no voltage at the screen output, which indicated a defect in it. Replacing the fly-back with one from Brasalfa, the defect was resolved, but the weave was excessively wide. After checking that tsound were no damaged components in that circuit, it was enough to enter service mode and make the correction. (One way to enter the service mode of this device is to simultaneously press the menu keys on the remote and on the TV panel for + or - 10 seconds.)littlecarlos
LGRP 20CB25A
MC 059A
I'm soundMemory 24c04Replace memory 24c04 horiginalluitvsom
LGLM-M730A
Weak audio (fanho)Stk 412-290Subtitle itJ.DANTEX
LGMC-59K - CP-29C84M
No on-screen functions (OSD)Diode d401 in surgeReplace diode d401, also check c402,c401 and follow the line. res: lack of pulse hcaio
LGCP20K40
When turned on, the TV turns off in less than 2 secondsI changed the processor. str6654, but it didn't solve it, it keeps turning offThen I decided to replace the memory (24c04), it was shot and dropped, it didn't turn off but it remained file, it was the memory that was the defectThis email address is being protected from spambots. You need JavaScript enabled to view it.
LGLH-D6235A
Cooler doesn't workApply thermal paste to the th300 thermistor and place it against the heatsink.Persio
LG21FS4RLG
Normal and completely dull soundI opened the jamp l-901 from the skrin grid and turned on the TV and it worked, then I just put the l-901 in place and that was it.Alvanyr
LGRP20CB25
Image without contrast normal menuDiodo d502 1n4148Edson Peixoto
LGRP-21FB32
Oscillates and cuts quickly and kills the 10 v voltageJust change the flex blah because tsound is a problem.maicon