PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4740
Results: 4740
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TV PH49F30DSGWA | TV turns on normally but no image bak language off | Cw825 short | marivaldo | |
PHILCO | PH40D10DSGW | Locked in logo | Change u203 rom memory or rewrite | Cabeça | |
PHILCO | PH28D27D LED | League without image with sound | Test it with an LED tester, the screen lights up, when it turns on, the inverter voltage goes up and then drops to 12v. | Open the screen and it will have 1 or two defective bars. | Techmix |
PHILCO | PH21MSS | Turns off after 5 seconds showing a colored line above the screen | Ic301damaged vertical outlet la78141 | Replaces ic301she is good again | Reis eletrônica |
PHILCO | PTV32G50SN | Image with curtain effect | CT909 capacitor with leak and shorted DT805 SMD diode | Changing the smd capacitor and the dt807 diode can use a diode with a7 nomenclature very common on t-con boards | TV CENTER GUAIBA |
PHILCO | PME25 | When you plug in the socket, the display keeps flashing and beeping. When you open the door, the plate and fan are activated and the beeps become very fast. | L1 changed, just change it. | Ferraz | |
PHILCO | PH39N86DSGW | Standby blinking continuously | The customer didn't tell me but he probably tried to update it and corrupted the TV's memory. | Pass on the software using a pendrive formatted in .fat32 | World TV |
PHILCO | PTV16S86D LED | Stby LED won't turn on blinking | Fountain pulsing | Photo of coupler position nw2 next to the transformer, when replacing the TV it worked perfectly again. | REAL ELETRON CARVALHOS MG |
PHILCO | PH40D10DSG | Reduce LED current | High voltage burning leds with 156 v | Considering 50 leds in series of 3volts each 150v remove r410 from 2r2 | BOSCO |
PHILCO | PH40U16DSG LED | TV does not turn on or the standby LED lights up. making clicking noises in the secondary of the power supply | Mosfet 14n25(qp401) and diode hbr3200(dp401) shorted. | I also replaced the electrolytic capacitors as a precaution. | Roger |
PHILCO | PTV55Q20SNBL | Plug it into the socket and the standbay LED blinks slightly and goes out | Cold solder not bga | Reballing | Marivaldo |
PHILCO | PH32E31DSGW | Loses sound or no sound | Q1a2 | Turn off transistor q1a2 | Lutec |
PHILCO | PH24B | No image | Tsound is no power supply to the c i inverter driver ic101 | Replace of open transistors q105 and q104(smd) and c131 10μF/50v | eletrônica Fernandes-to |
PHILCO | PH49F30DSGWAC | Normal sound, no image, backlight off | Diode sk320u position vw9 and vw10 shorted in the inverter circuit. | Replacing them. I didn't find the sk320, I put hbr3200 | WORLD TV |
PHILCO | PH4225DG-LED | TV turns on and off with standby LED blinking | Poor contact/cold welding on the power supply transformer. | Resolve or trafo | Milton Camargo |
PHILCO | PH4225DG-LED | TV turns on and off with standby LED blinking | Poor contact/cold welding on the power supply transformer. | Resolve or trafo | Milton Camargo |
PHILCO | PH24M | TV completely inoperative | Does not generate 12v in the secondary | Dead power supply did not generate 12v. I replaced the ic1 – tl7531a, the power supply worked more pulsating and did not stabilize. Replaced the ec2 - 22μF/35v, everything returned to normal and perfect functioning. | Airton Gervásio da Cunha |
PHILCO | PH40D10DSG | LED bar doesn't light up | Transistor mdd14n25 shorted and the 0.33 resistors open, gate terminal resistor 22r also open | eletmoraes | |
PHILCO | PH40D10DSGW VEX.PH.VÍDEO.211.REV.0 | Screen LEDs flashing quickly after a few minutes on | Rp408 from 470k com 488k | Ariel Santos | |
PHILCO | PH42E53SG | STBY LED is on and the TV won't turn on. | Lack of 24v power supply. | Test the p_on pin, if it has a voltage of +or- 2.5v. test the supply voltages of the ncp1397ag, if they are ok, replace the ncp ci. | EVANDO VIANA |