PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | 2140 | Cloth magtetizada | Saida is vertical | Defective vertical outlet | Roberto Consertos |
GRADIENTE OU PHILCO | TPF 2130 | Turns on and off as soon as the signal and video appears note: blurred as if it were a defective socket | Smd capacitor shorted vertically | Replace c 601 (smd) short and r708 open | George Pontes |
PHILCO | PCM1446 | TV doesn't turn on. | Defective power supply, zd904=30v zener with leak and r923=1r open. | I replaced the zener and the resistor and jewel. | Amando Olímpia. |
PHILCO | PCM2044 | No characters | R612 de10k | asbrito | |
PHILCO | PCS2952 | Flashing oled power without parazr | Power supply c 911 | luiz de sao | |
PHILCO | TPF29S4F | Cushion effect image | R1701 aberto 10r2w | GILSOM | |
PHILCO | PCM 1444 | Running away from color and shaking as if it were out of horizontal frequency | C205 2.2mf put new, close to the micro | This email address is being protected from spambots. You need JavaScript enabled to view it. Jaicós -PI | |
PHILCO | PHT550 | Does not read CD/DVD | Disc motor does not rotate (despite the voltage it did not work) | Changing the motor and 1r smd resistor on pin 12 of the c.i. motor drive. u4 (a5888s) | |
PHILCO | TP2053 | Didn't care | When connecting the TV to the socket, the LED turned on and the power supply in standby went to 15 volts. When activating the power power supply it rose to 115v and then dropped to 15v. I removed the solder from the +b of the fly and activated it and the 115 stabilized. I removed it the fly and put a test one and the TV started working again | Replace fly back | José Gusmão |
PHILCO | PCM-1451/2051 | Out of phase or shadow in the image and horizontally displaced | R710 changed zd702 8v2 with leak. | Replacement | alex/feteer |
PHILCO | TP20V56 | TV with everything magnetized image with blurred colors | Curto n q902 triac bt138 em | Connect it directly without a triac, close it, throw it away and as if it were a relay, turn on the demagnetizing coil when you turn on the TV, but other TC models do not use a relay or a triac | marcos melo cascavel ceara |
PHILCO | PSC-2976S | No contrast | Dz701 zener diode shorted | Replace for new zener diode | |
PHILCO | TVPH21B BRITANIA | Doesn't work | R552 - 100k 1/or | 100k was replaced to 130k | PIMENTA |
PHILCO | PC 1444 | Vertical closed, opens only about 5 cm | See r 615, open | Master Eletronica | |
PHILCO HITACHI | 20 | TV inoperative, burning fuse | It was the c904 shorted | Eletroclaudio Aguas Belas PE | |
PHILCO | TPF-2130 | Closes the image as if the negative voltage was missing at the vertical output | Glue that goes over the negative diode of the vertical output (d702) | Take it out if it resolves, then that was it | CSOM (66)34231060 |
PHILCO | CPH 06 20 | As na tv e sem as no av | Ci 18 legs | Bad the av pin goes tsound | negodrama |
TV PHILCO/HITACHI | PC-2035 CPH-03 | Only turns on after complete cooling | C925 4.7 uf 160v from power supply, zero capacitance | Substituted | GEORGE |
PHILCO | PCM2051 | Blinking led | +b ok I measured the +b of the T702 transformer and it was having too much consumption it should have been +or- 35v it only had 8v I noticed the fly back with heating, I changed it and it was ok | Replace flyback ov2094/d1 obs these flyback giving you a lot of defects as it had already been replaced days ago (I had 3 identical cases with this blessed fb and it wasn't cheap) | fernandocamarques |
PHILCO | TPF 2902AV | TV with black bands on the horizontal sides | C 706 as low capacitance | Also replace c708 | multsom |