PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PCM2043 CPH05 | LED flashes (standby) and seconds after switching on | C-722 470x16 volts alterado | Replace it with a new one, if resolved | Paulo Sertel Itararé SP |
PHILCO | PCM2144 CPH05 | Tremulous image | C-205 2.2x50 volts exhausted | Replace the c-205 with a new one and readjust the trimpot p-201 10k | Paulo Sertel Itararé SP |
PHILCO | TP14U56 | Without image, with osd and sound | D602 | Replace d602 with leak | joaomvjr |
PHILCO | TP20U56 | Without image, with osd and sound | D602 | Replace d602 with leak | joaomvjr |
PHILCO | PH29C | Blinking LED doesn't work | D 810 fr154 | macceletronica | |
PHILCO | TPW3280 | Tries to turn it on, it starts to activate but it doesn't work, the LED keeps flashing | Wide capacitor c708 5n6 | macceletronica | |
PHILCO | PCM 2044 | Only in stand by does not oscillate | Closing a short in the collector and emitter of the q 905 oscillates | Changing q904 or even leaving the short may not perform some functions but it works | celito santo angelo |
PHILCO | TP2052N | Turning off immediately after turning on | Dz101 3.9v with leak | Replace it | eletrônicatual [nen] |
PHILCO | PH 14C | Image erases and switches to one of the colors | Transistor bf 423 rgb output | eletronicaastec | |
PHILCO | DVD PH155 | Doesn't start | Defective photocoupler | Changing the photocoupler | johnny busnadiego |
PHILCO | TP-1452N | TV with normal sound / with characters / washed black screen, opens the normal retro screen | Replace flyback | DOIDO DA ANTENA (This email address is being protected from spambots. You need JavaScript enabled to view it.) | |
PHILCO | PCS-2976 | Blurry image.totally out of focus. | Circuito vertical. | Replace. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PVT2010 | Does not come out on stand-by | Saida Horizontal / Saida Vertical / Cop. 541 | Replace mentioned items | eletronicaapolo |
PHILCO | TP2053 | TV wasn't turned on, it just kept making noises from the speaker like toooooooooooooo | I checked everything on it and didn't find anything bad. | Then came the surprise: the magnet of the primary power supply transformer was detached, so I glued it back together and it started working again, and the very large transformer that is next to the MOSFET was either loose or detached; | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TP1454 | It just stays on stand by, +b voltage is around 30 volts and it doesn't work | D-908 shorted killing the 12 volts from the vertical | Replace d-908 | samuel leite |
PHILCO | PH21MSS | Does not turn on, power supply inoperative | Ic reg de power supply ncp1337p | BRUSKE | |
PHILCO | PCM 2044 | Vertical is from the position | After cold soldering vertically, the image was very open at the bottom and was not in the correct position | Replace c612 10μF x 50v e ajustar no trimpote ok | celito santo angelo RS |
PHILCO | TFP2121C | When pressing the "power" key, the standby LED turns off as if the TV were to start normally, but when horizontal it starts to oscillate, the power supply switches off and the STBY LED starts blinking. | C715 (6n8/ 1k6v) with low capacitance, measuring only 4n7 | Altevir Lima/ Valparaíso Eletrônica-PA | |
PHILCO | TVPH14C | Fully blurred screen with three vertical colors | Voltage that polarizes the vertical output (-13v) absent | Re-solder the vd 564 rectifier diode on the power supply transformer | guaracy borges |
PHILCO | PCM2046 | Does not turn on +b with 30v | Zd904 / r923 | Replace mentioned items | eletronicaapolo |