PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH28S63D | League has sound no image | All the LEDs shorted, I replaced them all and I also changed the power supply to a toasted L6 coil and leaky MOSFET, the original is not sold. | Defect resolved | Carlos |
PHILCO | PH32B FSP180-4H02 | Dead power supply, doesn't work | Dead parts: ec1(100uf/450v), q5(5n50), q6(5n50), f1 (4ah 250v) fuse. | Also check: c5 (10μF/35v), c36 (10μF/35v), c14 (47μF/35v) and d1 | Kaya Elektronik09 |
PHILCO | PH39U21 | Back light access, with sound and functions but without image | Open diode on the display board, position d204, also check d205, diode a8, I didn't have the original, I put a 1n4148 and it worked | Eledine | |
PHILCO | PH29MSS | TV with excessively wide image | Shorted regulator q431 cs630f | Just replace it with the same one and it's fine | Evandro simao |
PHILCO | PB330BT | Turns off after 30 seconds | Very high voltage on 1c4 3.3 volt regulator (PCI microcontroller panel) | Changing resistor r217 from 10Ω to 56Ω | FABIO |
PHILCO | PH29B | Without image on TV and AV, with characters | Unconfigured memory | Data rewriting | Imagem |
PHILCO | PH21SS | TV turns on then turns off | Capacitors c562,c563,c450 | Replace capacitors c562, c563 1000u25v and c450 2kv680p | marquinhos eletronica |
PHILCO | TP2053 | I'm sound | Tv phico trc tp2053 without sound, enter service mode, go to the page wsound it says model, evg, 12er, syscol... and set the model to 18. * service mode: 1st with the ac cable disconnected, press menu and connect the ac cable, without releasing the menu key 2nd ... without releasing the menu key, press the vol+ key and keep both pressed for 5 seconds. 3° release both keys and turn on the device. 4° wait until the image appears. then press the menu key. to navigate in service mode use the cursor keys on the cr or the vol and channel keys on the panel... change the model code to 18.. | DJ PITUKA | |
PHILCO | PH40U16DSG | TV turned on normally with the LEDs on without image | Capacitor on the v.com shorted, I just forgot to write down the number on the board, the fuse was open, it's on the opposite side of the fuse on the v.com, change the capacitor and the TV will be fine | Replace | <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> |
PHILCO | PH21M SS | Turns on when images appear turns off | Toasted r816a heating smoked | Replace q802 2n5551 ebc with bf422 see polarities ecb r816 with 330r 1w q804 bf422 d815 1n4007 replace without testing | ASL ASSISTENCIA TÉCNICA TONINHO |
PHILCO | PME25 PME-25 | When opening the door, the plate and fan rotate. | Main relay (smaller relay) tested the microswitches and high relay note: disconnecting all connectors from the PCI panel when opening the plate and fan will rotate as the relay controls it, keeping the light on. | Replaced relay and cleaned door keys. electrical diagram https://www.electronica-pt.com/esquema/microondas/philco-pme25-microondas-65741/ | Pedrozo |
PHILCO | 2130 | Vertical closed | R 708 e d 702 perto do flay back. | Tec. zidane | |
PHILCO | PH39U21DSGW | TV turns off after about 15s to 30s on | Flash memory | Software update from the philco website, place a pendrive formatted with the drives and turn on the TV, quickly: open the menu, options, software update (usb), volume - (yes), and the TV will go into update | Teclados e Cia |
PHILCO | PH21C | Turns on normally, with a slightly stretched width, and turns off after a few minutes and giving 130v at the power supply while normal and 102v | Changed resistor r839 from 82k giving 102k, just changing it returned to normal. | Replaced resistor r839 from 82k giving 102k, just changing it returned to normal. | DJ PITUKA |
PHILCO | PH21MSS | Turns on, tsound is no signal but tsound is no image even on the AV | After banging my head a lot I found the Q301 and Q401 defective | The replace of q301 and q401 and running into the hug | Eletronica Carlos Viseu-PA |
PHILCO | PH14 D | The tsh does not oscillate, when connecting b+ 105v and it drops to 16v, q401 oscillates but q402 does not trigger. | Missing +12v for the t402, track oxidized by cockroaches | Retrace the trail. | GDP2 |
PHILCO | TV PH21M SS | The TV works normally but after a few minutes the image turns white with the screen full of retrace lines | Q802 | Replace or q802 | Sinailson furtado |
PHILCO | PH19C LCD | Red led | D002 open, flashing | Replace both diodes as a precaution | OLIMPIO- WATEK |
PHILCO | PH32U20DSWG | The original board was scorched caused by lightning, I bought a board and it had the following defect after the change, the TV turns off after 40 and 50 seconds | Software corrupted or incompatible with the screen, in this case I solved the problem by removing the memory from the old board and putting it in the new one. | Try updating the TV with original firmware, if the problem persists even after updating, remove the memory from the old board and place it on the new board. | Eletronica ALLFATV |
PHILCO | PH42M61DSGW | Turns on the logo appears and turns off | Problems with the update. After carrying out the update procedure, the problem was resolved | Paulo Russo |