PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TP2054 | TV starts working + no image appears. waiting about 5 seconds. appears with a smooth screen, with vertical and horizontal lines wanting to close. | Change the cap. 6n8 x 2kv. which has a low value. (5n6 x 2kv) | ROBERTO PINTO | |
PHILCO | TPF2922 | Normal league, with horizontally expanded image | The dz1701 was replaced | ROBERTO PINTO | |
PHILCO | TPF2922 | Sometimes it turns on, sometimes it doesn't. When it turns on, it has a black stripe at the top and bottom, with excess red in the image. | The precision resistor r725 was replaced and an adjustment was made to the flyback screen | ROBERTO PINTO | |
PHILCO | PC1443 | Vibrating t901 (power supply buzzing), not having high voltage. | C921 to power supplys. | C291 de 22n/50v | Ademir tc |
PHILCO | PCM2044 | Doesn't catch any channel | Ceramic capacitor | Ceramic capacitor on pins 42,43 and 44 responsible for inputting vhf,μHf and vl signals | WILLIAN8952 |
PHILCO HI | PC1442 | No sound normal image | C420 shorted | Replace | EletroClaudio Aguas Belas |
PHILCO | PH200 | Inoperative, only blue volume LED on! | Open smd l4 inductor | Replace l4 for another... | pfa |
PHILCO | TPF2121F | The TV only turns on by pressing the power button on the panel, that is, it does not turn on with the control. | Defective sensor, position ir1101 which is on the plate on the front panel of the TV, sensor rpm-693b. | It was replaced for an identical one and it looks great!... | Armando de Olímpia |
PHILCO | TP-2052N | Dark screen with no image and with normal sound when the screen increases, a torch appears like an arcuires | Defective vertical output tda8356 | Replace | EletroClaudio Aguas Belas |
PHILCO | PCM2044 | Poor convergence, in the image and characters, and heating up r711 | Oxidized deflector coil | Replace deflector | PALAURO |
PHILCO | PT | Power supply did not oscillate | Ic do som | Replacement | |
PHILCO | PCM-2051 | Volume increases or decreases every 10 points | Memory defect | Reset the memory: unplugged, press and hold the ch+ and ch- keys on the TV. Turn on the power and wait about 5 seconds until the stand-by LED lights up. release the pressed keys and turn on the TV and reprogram the channels and settings. If the defect returns, replace the memory and perform a reset. | Diego PG-PR |
PHILCO | PCS-2976S | Resolder tube board 6 wire mesh | Resolder | SEM IMAGEM TELA AZUL COM RETRAÇO | |
PHILCO | PCS-2956N | Works for a while and turns off | Weapon protection | I removed the resistor r 932 and it worked normally | noel batista |
PHILCO | PH200 | Does not turn on as if the power supply has a problem | Remove the tda7265 sound output, if it turns on, replace it | Replace sound output | Cezar |
PHILCO | PCM 2051 | The TV turns on and off in seconds | R 705 3r3 measuring good to put a jamper | eletronica rodrigo 048 32429465 | |
PHILCO | TP2920 | When it turns on, the LED goes off, the tube blinks a few times and goes off, then the LED keeps blinking | Changing capacitors c1701 and c 1703 6n8x1k6v polyester.......it was zero again!!!! | adilson | |
PHILCO | PH14C | Dark image | BF 422 and 423 leaking, change all BF's on the TRC board | Continental | |
PHILCO | PCM 1444.2044 | No color. | Swap.c.504. | Resolved | hermildon jose t de sousa |
PHILCO | TP14U56 | When plugged into the socket, the power supply gave a signal that it would work but it didn't, and the LED didn't even light up. and the +b voltage was just 10v and the normal 4.7v voltage | R107 of the LED and e-prom system was open and the sw101 was broken. | I replaced the touch switch on the power sw101 and it turned on but the LED didn't work, I replaced the 100k or107 and the LED came on then it was just a hug. | DIGITEC ELETRONICA (65)9608-4535 |