PHILIPS TV Repair: Common Faults and Solutions.

Search: PHILIPS
Results: 14168

PHILIPS Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem	Solution	By
PHILIPS	40PFL3606 L11M1.1L LA	Image with gray streaks and flickering	240k resistor 3j26 is just above the 5-terminal a1 ci, close to the 7j00 ci		Ariel Santos
PHILIPS	47PFL3007D/78	After a few minutes on, it makes a hissing sound, stripes on the screen, turns off, turns on with no image	U701, 3.3v regulator, change!		Rodrigo cofferi
PHILIPS	FWM663X/78	Does not turn on, just stand by	L1 open corroded by glue.	Clean the glue from the entire board, remove the coil and resolder the corroded terminals, no need to replace
PHILIPS	42PFL3604/78	Does not turn on, standby on.	Exhausted solid capacitors.	Substituir c474,c106, c526,c529.	2D Eletrônica e Refrigeração.
PHILIPS	32PFL3707D/78 32PFL3707D	Turns off by itself, emits a beep, turns off the screen, drizzles, 3.3v regulator with 4v	Metallic capacitor c9111 and 3v3 regulator u701		JOHNATAN
PHILIPS	50PFT4509/12 TPM14.1 ELA	TV doesn't work. the STBY LED doesn't even light up	Power supply works well. This TV gave me some trouble, as I didn't find any shorted components. After so much analysis, I replaced the 27MHz x4000 crystal and everything went back to normal.	Replace x4000 27mhz crystal.	Jose Almeida Tavares
PHILIPS	14PT414	LED blinking and won't turn on	Resistor 100r position 3248		Fofao
PHILIPS	50PUG6554/78	Does not turn on or stand by	Power outage	Replaced fuse and q9101 and q9102	Eletrônica newton
PHILIPS	FEM583	Hissing at the outputs with very low audio	Z3,r48, responsible for -12, and one of the ic:308,309,or 310 shorted	Replace the zener diode, the resistor and the IC that is shorted	Rodrigo cofferi
PHILIPS	32PFL4017G/78 1L LA	It turned on if it turned off, it took a while to turn back on	Protection acting.	Uu701 regulator replaced to more. tension measured 3.8 volts. normal 3.3 volts	Carlos Almeida
PHILIPS	40PFL3805D/78	Turns on the logo appears, backlight flashes 3 times and goes off, normal sound	Put a 10k resistor from pin 15 of the backlight ic oz9977 to ground		Eletrônica Oliveira
PHILIPS	29PT558A/78	Turn on then turn off	After changing several parts, including capacitors, resistor, photo coupler, I checked the sinoscope plate, I did everything and nothing found that the defect was in the tube, it was easy to solve. Not too strong so it doesn't break. Once that's done you can mount the TV and it's ready.		Alexsandro
PHILIPS	22PFL2807H VES1.1E LA	The std-by led does not light	Diode d25 (sb5100) shorted to 12v supply	Replace diode	valecovo
PHILIPS	32PFL5403/78	Disappearing image	Lubrication of main board contacts with t-con		Marcelo
PHILIPS	42PFL3604	So stand by	Capacitor c474, next to the crystal on the main board, next to the p21 connection next to the TV's USB		Wesley Borges 7
PHILIPS	58PUG6900/78	Turns on more with the blacklight off	Transistor aqp1 and aqp3 on the inverter board, both with very high esr	Replace the 2 transistors which are originally b414, as I didn't have the original I used the fdd8447l and it worked normally	George Luís
PHILIPS	32PFL3008	Turns on backlight does not appear immediately, then backlight turns off, LED stays on as if it were on stand-by	When checking the voltages, I noticed that they were all ok, including vgh and vgl, so I re-recorded epron, resolved	Eprom	Eletronica tensao R Jacuipe
PHILIPS	231TE4L8/57	Doesn't start.	C910		Osvaldo AB
PHILIPS	42PFL6007G/78	Locking volume doesn't go up, doesn't change channel	Nand memory, ic 7700 I replaced it with a recorded one, the TV was great		Marcelo
PHILIPS	42PFL4007G	Turning off over time	Sound output ci u603 sta3818w smd (put your finger and check for uncontrolled heating)	Replace it (in some cases putting a tripod on it solves the problem)	orlando lott