PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 32PFL3605D/78 LC10.1L+LLA | Gray image, with horizontal lines and blinking | R3j18 (r750k) aberto ( vgh_35 ) | Replace r3j18 | leitemarcellus |
| PHILIPS | 20PT3331 | White lines on top of the screen | 2465 with 10mf, I had put a 47mf one and it didn't solve the problem and the voltage was at 12v and when I put a 10mf one it went up to 18v and the TV was normal. | Eliel Magno | |
| PHILIPS | 40PFG4109 | After changing the LED bars, 1 bar does not light up | The original buses have the central and positive pins with jumpers | Jumper the central and positive pins on the middle bar and the bar that did not light up. (check the pins carefully so as not to jump with the negative). | MarceloTJ |
| PHILIPS | 40PUG6300 | The TV turns on, then the speakers beep loudly and disarm. stand by stays on and no longer turns on. When unplugging the power, the TV sometimes turns on and then turns off with a beeping sound from the speakers. This defect can also leave the TV inoperative with the stand-by LED on. | In my case, the defect was in the smd transistor sot23-8 (q702), the transistor code is aon4421. This transistor is intermittent, killing the +5v_sw, which is around 0.35v more or less. all other voltages appear normally. | Before changing q702, solder pins 5 and 6, first removing q702 from the circuit. If the TV works again, just replace Q702 and go hug. | AASF |
| PHILIPS | 40PUG6300 | The TV turns on, then the speakers beep loudly and disarm. stand by stays on and no longer turns on. When unplugging the power, the TV sometimes turns on and then turns off with a beeping sound from the speakers. This defect can also leave the TV inoperative with the stand-by LED on. | In my case, the defect was in the smd transistor sot23-8 (q702), the transistor code is aon4421. This transistor is intermittent, killing the +5v_sw, which is around 0.35v more or less. all other voltages appear normally. | AASF | |
| PHILIPS | 40PFL9605D/78 | Tip: If you have a TV of this model and turn the Stanby LED on and off, it flashes 9 times | Disconnect the speaker from the main board, the impedance of the speaker may be altered | In my case, that was it, I replaced the speakers, replaced impedance, just replace it and run for the hug | valdir anizio |
| PHILIPS | 42PFL4007 | ECD key fail message appears on the screen | Plate from 32" to 42" or vice versa | Rewrite eeprom memory u409 | ArnolTec |
| PHILIPS | 43PFG5100 | Tsound is no audio | Change q706 | Agnaldo | |
| PHILIPS | 32PFL5604/78 | Standby LED lights up red, does not turn on and does not accept commands | C474 4.7uf/16v next to the usb port, next to a cystal. | Replace without measuring | Eletrônica Barbato |
| PHILIPS | 32PFL5604/78 | Standby LED lights up red, does not turn on and does not accept commands | C474 4.7uf/16v next to the usb port, next to a cystal. | Replace without measuring | Eletrônica Barbato |
| PHILIPS | 47PFL8606D | Stand by LED blinks twice and does not turn on | IC 71 D0 or 71 D1 capacitor burns | Replace the 10 μF capacitor and the 1 u40 fuse | Marcos elétricos |
| PHILIPS | 43PFG5813 | TV inoperative, no stand by but power supply working normally | Power supply with normal voltage +5 stb but without voltage +5 sw that leaves the fet q706 and feeds u705. | Replace of q706. | ToniTec |
| PHILIPS | FR 310 | Channel with very low sound, loud crackles in the channel | Preamp input capacitor 139 had low resistance >200r - replaced/resolved. | gdikastro | |
| PHILIPS | CDC265 | Drawer doesn't open | Gear with integrated motor pulley unlocks broken drawer or drawer with hardened grease | Gear shaft lubrication/gear replace | |
| PHILIPS | 39PFL4707 | Inverted image after changing the board from another model | The code is 165 for the 39pfl4707 with chimei innolux display: tpt390j1-hj1l02 rev c1c. | First try to enter the code: menu 1999 return and go to display id and enter 165 or 062598 menu 165, the TV turns off and when turned on again it will be at code 165. if that didn't work, first of all update the TV to the model correct via pen drive, after doing this, carry out the procedure of pasting the code, in my case it only worked after I updated and then I entered the code and the TV disinverted the image. | MIGUELTV |
| PHILIPS | MINI HI-FI SYSTEM FWM210 | Does not turn on, just blinks little dots | Swollen capacitor in power supply C509 (2200mf/25v) | orlando | |
| PHILIPS | 14PT3131 78R | Turns on with RGB lines at the top of the screen and turns off in 3 seconds | C2460 (68nfx250v) with problem. the capacimeter measures normal | If you can't find it, you can put one with 100nf 250v. | Rondy Eletrônica |
| PHILIPS | 42PFL5332/78 | Turning off intermittent | Photo defective couplers | I replaced all photo couplers with 817 and pc123 (that's what I had in the scrap) | Respawn Tech |
| PHILIPS | 50PUG6102 | Doesn't start | Power supply | Diodo fr107g (d9103) | Brackmann |
| PHILIPS | 50PUG6513/78 | Works after a short time turns off voltage of 5 volts in coil l702 low and variano | U708 with oxidation, clean with thinner | Robison oliveira |