PHILIPS TV Repair: Common Faults and Solutions.


AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HISENSE
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: PHILIPS
Results: 14174

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPSFL2.26
Overview of sops repair kitsOverview of sops repair kits ---------------------------- fl1.0 ag00 upto ag03 4822 310 20492 fl1.0 ag04 and higher 4822 310 31921 fl1.0s 4822 310 31924 fl1.1 25" and 28" 4822 310 31919 fl1.1 33" 4822 310 31932 fl1.1s
PHILIPSFL2.26
Osd, txt, sound, colours ok, no y signal.C2396 (22nf) leakage (4822 126 11544)
PHILIPSFL2.26
Noise on high volumePerform the following modifications on the ssp: add on position 3618 4,7nf (4822 122 31784) add on position 3619 jumper (4822 051 10008) connected in series from 2604/4610 to earth. change position 4610 into 1kΩ (4822 051 10102)
PHILIPSFL2.26
No sound, "on, standby, i" leds blinking10mhz crystal 1602 on the ssp defective, 4822 242 80276
PHILIPSFL2.26
No colors in tv modeCheck ic7365 (tda4650) on the ssp (4822 209 30837)
PHILIPSFL2.26
ModificationModification ------------ on scavem amplifier panel 4822 212 31259 position 2671 and 2672 are changed from 680pf into 330pf (5322 122 31842). this modification is introduced from start production onwards.
PHILIPSFL2.26
ModificationModification ------------ only for 25" during production in week 9405 the picture tube of the 25" sets has been changed from the a59eak252x43 (4822 131 20501) into a a59eak252x44 (4822 131 20602). this new picture tube is used in sets with serial number
PHILIPSFL2.26
Low frequency hum from subwoofer, buzz from right hand squeeter.Check dc level on pin 1 and 9 of ic7011 (tda1521). if not correct, replace (4822 209 63913).
PHILIPSFL2.26
Low brightness txt and osd, picture okIf this condition occurs, check the option codes. resetting the option code numbers as per the service manual provided the cure.
PHILIPSFL2.26
JitterIn pip unit change the value of r3336 to 4k7.
PHILIPSFL2.26
In default mode err.99, blinking leds. no +5.4v on pin 8 l02Ic7551 lm358n defective +5/13v, replaced. (4822 209 70672) cause: bridge 9240 interrupted.
PHILIPSFL2.26
How to enable/disable "child lock"Press "menu" button on remote control. when the menu appears on the screen, you select "special features" (this expression is language dependent) within "special features", the "child lock" can be enabled or disabled.
PHILIPSFL2.26
Four dark bars over the picture.The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672).
PHILIPSFL2.26
Foggy picture/fly back lines/protectionCheck/replace r3517 1Ω on lsp (4822 052 11108).
PHILIPSFL2.26
Dark picture, only green led, no menu or osd.+5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954).
PHILIPSFL2.26
Dark fuzzy picture. osd and menu not in focus.+5v was 7.8v and +13v was 15.5v ic7551 (lm358n; 4822 209 70672) defective.
PHILIPSFL2.26
Crazy behaviour: no response from rc or controls.Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v83 (4822 900 10506). for easy mounting also the controlboard 7115 (on ssp) can be replaced by
PHILIPSFL2.26
Correction to the service manualCorrection to the service manual -------------------------------- in circuit diagram b on page 7 of the service manual fl1.14/fl2.14/fl1.16/fl2.16 and fl 1.17 the resistors 3624 and 3625 are not drawn. these resistors should be drawn on the position of 96
PHILIPSFL2.26
Correction to service manual flx.14/16/17Correction to service manual flx.14/16/17 and flx.24/26/27. ----------------------------------------------------------- the code number of position 1200 (fuse 3,15 a) is wrong. the correct code number is 4822 070 33152. this fuse is situated on the lsp i
PHILIPSFL2.26
Correction to service manual fl2.24/fl2.26/fl4.27Correction to service manual fl2.24/fl2.26/fl4.27 aa ---------------------------------------------------- the following position numbers are mentioned wrong in the stocklist of the scavem filter panel (page 35): 2512 4822 122 33496 100nf 10% 63v 3527 4